Setup 4 Nail at 0.5 + 0.1l cm String/Spring Scale at 89.2 + 0.5 cm Hanging mass at 57.8 + 0.5 cm 0- 64 + 1 degrees

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: kat Drill, 2 Holes 92 24 40 1 Drill 7 314 3 34 31/12 1 Drill TRA 21

A: Given: Draw the isometric view with dimensions

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: Successive approximation ADC explian

A:

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: w of sine's when ( a= 100° , A=10.8 B=6

A:

Q: 12-x2 了了少 Je

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: 8. 000 *性 10 20 G- 020 10 74 100 140 Rajah L8

A:

Q: he figure shows the multi-views and of components of a 3D RINTER HEAT BLOCK ASSEMBLY. raw to a scale…

A: All parts and assembly are provided below. 1 :…

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: We need to calculate the hydrostatic force acting on the sluice gate

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Y 8 12 8 12 R= 3

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Draw front, top and then left side view.

A:

Q: z=(x-a} +n(y+b)° 8. Consider the following statements (which statement(s) is/are correct): =2,…

A:

Q: how did the equation simplify to a = 0.984?

A:

Q: * Ce fea dendn D d f N

A: Normal stress is defined as the intensity of force acting over a unit area in perpendicular…

Q: y (x- 6y)dx - x (2x - gy) dy = 0; x =1 , y = 1

A:

Q: How is the shear center determined?

A: Shear Center The shear center is a point on the section of the beam, from where the resultant load…

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…

Q: Need three views

A: According to the details provided in the question, we need to find three views.