separate sheefs of paper. complete appropriate free-body diagrams. Problem 1: If the beam is made from wood having an allowable shear stress tatow = 500 psi, determine the maximum magnitude of P. Set d = 5 in. Fint2nt-2n 2 in. Problem 2: The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Determine its smallest diameter d if the allowable bending stress is aatow = 200 MPa. 12 kN/m 3m 1.5 m Problem 3: Determine the maximum shear stress in the T-beam at section C. 10 kN/m 150 mm 150 mm 30 mm B 0 mm SITY

separate sheefs of paper. complete appropriate free-body diagrams. Problem 1: If the beam is made from wood having an allowable shear stress tatow = 500 psi, determine the maximum magnitude of P. Set d = 5 in. Fint2nt-2n 2 in. Problem 2: The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Determine its smallest diameter d if the allowable bending stress is aatow = 200 MPa. 12 kN/m 3m 1.5 m Problem 3: Determine the maximum shear stress in the T-beam at section C. 10 kN/m 150 mm 150 mm 30 mm B 0 mm SITY

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ANSWER ONLY AC BC CDwrong answer gets downvote so double check the answer cause it will be input in the system
The allowable shear stress is τallow=895 psi�allow=895 psi. The supports at A� and B� are smooth
Pls answer ASAP. Thank you!
Situation 13 - Using method of sections, determine the internal force of members 3-6 and 5-7. Use L = 2 m and P = 3 kN. 2P P 3P 1² M 45° 45° 3 L L 45° →→X
Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 135 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). P (1) O 12.85 in. O 14.78 in. O 7.72 in. O 9.47 in. O 11.75 in. 0.5 in.-k 6 in.
IVEN: A 20-ft beam is subjected to the distributed load show. 0.75 in. 6 in. -3 kip/ct A B K-8ft →→ 12 ft SOLUTION: TOT 12 in. Beam Cross Section 0.75 in -0.5 in. A S B FIND: a. The bending stress at A. b. The bending stress at B.
1. Answer Set A only
Q.
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTION AND FBD. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. Solve for the stress of all members (AB,AC,BC,BE,BD, CE,DE,DF,EF,EG,FG,FH,GH) for the truss given below. The cross-sectional areas of the members is as follows Top and Bottom Chords = 350mm, Post = 300mm, Web/diagonals = 250mm.
Please write All answer in mpa