Select the correct answer.1- In figure (1) what the type of geara- Rack and pinionC- Spur gearFigure (1)b- hypoid and spire gearsd- helical and herringbone gears2- The distance between corresponding profiles of adjacent teeth measured along the base circle is :b- Circular pitchBase circlea-Backlashc- Base pitchd-3- Backlash (TB) is the distance between the space and tooth thickness, as measured along the pitch circle, inactual the backlash should be zero.Trueb- Faisea-4- The size of gear is usually specified by.a- Diameteral pitchC- Base circleb- Pitch circle diameterd- All of them5- The tooth thickness and tooth space measured along the ...b- addendum circlededendum circlea-base circled-C- pitch circle6- The point C & D are inside of point A & B this indicates interferenceb- FalseTrue -a-7- When the gear with large pressure angle, the diameter of the gear isb- biggera-Smallerc- Same diameter8- To eliminated interference byb- Using large pressure anglea- Using more teeth on the gearc- Using shorter teethd- All of them9- For checking no interference in the teetha- Lap

As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Select the correct answer. 1- In figure (1) what the type of gear a- Rack and pinion c- Spur gear Figure (1) b- hypoid and spire gears d- helical and herringbone gears 2- The distance between corresponding profiles of adjacent teeth measured along the base circle is : b- Circular pitch d- Base circle a- Backlash c- Base pitch 3- Backlash (Tp) is the distance between the space and tooth thickness, as measured along the pitch circle, in actual the backlash should be zero. a- True b- Faise

Select the correct answer. 1- In figure (1) what the type of gear a- Rack and pinion c- Spur gear Figure (1) b- hypoid and spire gears d- helical and herringbone gears 2- The distance between corresponding profiles of adjacent teeth measured along the base circle is : b- Circular pitch d- Base circle a- Backlash c- Base pitch 3- Backlash (Tp) is the distance between the space and tooth thickness, as measured along the pitch circle, in actual the backlash should be zero. a- True b- Faise

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4- Find the gearing ratio for the given compound gears shown in figure 10. 5- Given that the torque (t) of the driver gear is (40+x) N.m, find the torque of the green gear. (x is the last digit of your ID) (M) rrrrv Figure 10 Figure 11 D Error
Identify label A in the following spur gear diagram. A E Tooth thickness Width of space Pitch circle B H. Bottom land -Fillet radius F- G. Select one: a. Pitch O b. Working Depth O c. Whole Depth d. Involute e. Addendum O f. None of these Face width Top land
A spur gear set is cut with a hob. The spur gears have a pressure angle of 20 degrees and a diametral pitch of 16 teeth/inch. The pinion has 32 teeth while the gear has 80. The customer wants to replace the spur gear set with a custom helical gear set. The only requirements are: (1) the same hob must be used (2) the gear set center distance must remain the same (3) the gear ratio must remain the same. The designer has decided to use a helical pinion with 28 teeth. For the helical gear set, select the proper helix angle that will guarantee the three requirements. Report your answer in degrees, 3 decimal places.
(Helical Gear) 11 A helical gear having a 14.5 degree normal pressure angle and transverse diametral pitch of : per cm, the helix 10 angle is at 21 degrees and has 19 teeth. Compute the transverse pressure angle in degrees.
1. The figure shows a pair of shaft-mounted spur gears having a diametrical pitch of 6 teeth/in with a 14 tooth pinion (gear 2) driving a 49 tooth gear at a pressure angle of 20°. The power input is 3/4 hp at 2400 rpm cw. A, B, C, and D are bearings. 3. 3 in 3 in Determine the following: a. The Free Body Diagram for both gears. b. The pitch diameters of gears 2 and 3. c. The transmitted load. d. The torque Tin on the pinion shaft. e. The radial and tangential forces on gear 3 f. The output torque of gear 3 shaft.
Asap please
In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA-20;TB-60; Tc-140;TD-40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates C140 120 Output D 40 60 20 Input
Two mating 12-pitch gears have 18 external and 48 internal teeth, respectively. Determine the following: Their pitch diameters. • The center distance.
What is the solution for this?
The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears 40 teeth 490⁰ B 70 teeth 50 teeth