I. Select an example from the list of each Structural Shapes. Copy the properties such asmass, area, depth, etc. Discuss the meaning of the designation ( dimensions of the parts ).1. W shape2. S shape3. C shape4. Equal L shape5. Unequal L shape6. WT shape. Select a W shape to split fromII. Answer the following:1. What is the value of the resistance factor for gross area in LRFD?2. What is the value of the resistance factor for net area in LRFD?3. What is the factor of safety for gross area in ASD?4. What is the factor of safety for net area in ASD?5. Write the formula for the general formula for the shear lag coefficient.6. Write the value for the shear lag coefficient for the alternative value for W shapeconnected to the web with 4 or more fasteners in the direction of loading.7. What is the formula for the allowable strength in ASD?8. What is the formula for the designed strength in LRFD?9. Write the factored load combination in LRFD for dead load, live load, with earthquakeload, and snow load.10. Write the factored load combination in LRFD for dead load, with earthquake load, andwind load.

1. W Shape: The W shape is a structural steel shape with parallel flanges and equal web and flange…

Select an example from the list of each Structural Shapes. Copy the properties such ass, area, depth, etc. Discuss the meaning of the designation ( dimensions of the pa W shape S shape C shape Equal L shape Unequal L shape WT shape. Select a W shape to split from Answer the following: What is the value of the resistance factor for gross area in LRFD? What is the value of the resistance factor for net area in LRFD?

Select an example from the list of each Structural Shapes. Copy the properties such ass, area, depth, etc. Discuss the meaning of the designation ( dimensions of the pa W shape S shape C shape Equal L shape Unequal L shape WT shape. Select a W shape to split from Answer the following: What is the value of the resistance factor for gross area in LRFD? What is the value of the resistance factor for net area in LRFD?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There are 16 beams in the second floor of a house with a typical width of 400mm and depth of 300mm for architectural purposes. The total length of the beam is 40m what is the total square meters of plywood for formworks? Assume 5% wastage Choices 44, 17.6, 48.3, 46.2, 43
For the composite area shown, calculate the moment of inertia about X and Y axes. 95 mm Ŕ = 60 mm 55 mm 35 mm 70 mm 80 mm 125 mm
W A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the tensile stress in ksi? Answer to two decimal places. Type your answer...
2. In engineering, the modulus of elasticity is a way to measure how much an object deforms along an axis when opposing forces are applied among that axis. The formula can be expressed as E (F2-F)Lo where E is (82-81)A' %3D the modulus of elasticity, F is the axial force, & is a deformation measure, Lo is the original length of the object, and A is the cross-sectional area. Part A: Reaange the elasticity formula to find the cross-sectional area, A.
Note: careful with given dimensions. Give me right solution with clear calculations step by step. Don't copy from other experts solution
From the given axis determine the location of the centroid of the composite section shown in the figure. 50 30- 40 15 Dimensions in mm Match each item to a choice: Xbar Ybar Choices: : 63.2mm : 25mm :: 66 98mm :: 76 3mm
The rectangular wood beam is loaded as shown in the figure. 12 kN. 8 KN/m 150 m 250 mm 10m 2 m What is the bending stress in the beam 2 meters from point A? 7.68 MPa O 5.76 MPa O 10.24 MPa 4.48 MPa What is the bending stress 50 mm from the top of the beam 0.5 meters from point A? * 3.456 MPa 5.760 MPa 10.245 MPa 6.144 MPa What is the shear stress in the beam at point C? O0.48 MPa 0.80 MPa 0.64 MPa O0.32 MPa
10 cm 10 cm 15 cm 15 cm 75cm 15 cm Given the composite shape, find the centroid along y-axis.
1. For the 15 foot copper bar shown in the figure below, find the total elongation (or shrinkage). The bar has a square cross section of 2" x 2" ( 16,000 lbs 4000 lbs 12' Punch Force 12000 lbs 2. A metal plate is 125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi.
VE 4-4 Select the lightest C6 shape member, using the LRFD method, to resist tension loads of 30 kips dead load and 40 kips live load. The member is 10 ft long. The member, shown in Fig. VE 4-4 0, is A36 steel with F, = 58 ksi and is welded only on the end of the channel. Neglect block shear. Gusset plate C6 T T 6 in 6 in FIGURE VE4-4
Civil Engineering Calculate the web in-plane bending buckling strength of a panel rib for: web thickness tw = 2mm web height bw = 40 mm effective modulus E = 8,044 N/mm2 %3D effective Poisson's ratio v = 0.25 in-plane bending buckling constant kb = 24 for all edges simply supported %3D Reduce the buckling constant by a factor of 10 for free edges Quote the value in MPa to one decimal place.
Forces intersecting at a point given in the figure system, resultant of "F", 25kN and 24kN forces Since "R" is the force "F" and "R" Calculate the force. Of the composite with the horizontal axis the angle it makes is = 32.50.