u, A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Et = 2.1 x 10° MPa, Eai = 0.703 x 105 MPa, v = 0.3, vai = 0.33) E = .v = Seterel Faxial Fahuminum 3000 N A-500 mm A-500 mm Fahuminum? 3000 N Steel Alumin um

u, A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Et = 2.1 x 10° MPa, Eai = 0.703 x 105 MPa, v = 0.3, vai = 0.33) E = .v = Seterel Faxial Fahuminum 3000 N A-500 mm A-500 mm Fahuminum? 3000 N Steel Alumin um

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
The critical bending compressive stress in the extreme fibre of a structural steel section is 1000 MPa. It is given that the yield strength of the steel is 250 MPa, width of flange is 250 mm and thickness of flange is 15 mm. As per the provisions of IS: 800 -2007, the non-dimensional slenderness ratio of the steel cross-section is (a) 0.25 (c) 2.00 (b) 0.75 (d) 0.50
DISCUSS THE STRESS-STRAIN RELATIONSHIP SHOWN BELOW: (WRITE IN ENGINEERING LETTERING) Actual Rupture Point Ultimate Strength Elastic Limit Yield Point Rupture Point Proportionality Limit STEEL: Stress, o – Strain, e Relationsip
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
A 100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa Vxy = 0.25 Vxz = 0.5 Vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, ox,Oy,Oz•
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
Determine the ductility of the following steel samples that undergo tensile strength test. All dimensions in millimeter.
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
1. For the 15 foot copper bar shown in the figure below, find the total elongation (or shrinkage). The bar has a square cross section of 2" x 2" ( 16,000 lbs 4000 lbs 12' Punch Force 12000 lbs 2. A metal plate is 125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi.
A force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and having a yield strength of 400 MPa and a tensile strength of 480 MPa,Determinea. whether the bar will plastically deform; andb. whether the bar will experience necking