section of a rotating shaft is under an alternating bending moment of 70Nm and a torque of 35Nm. The yield strength of the material is 560 MPa and the ultimate tensile strength of the material is 700 MPa. The estimated actual endurance strength is assumed to be 210 MPa and the stress concentration factor is 1.5 for well rounded fillet. (Design Factor = 2) Determine the minimum diameter of the section of the shaft: D =  mm

Q: A compound steel [G = 70 GPa] shaft consists of a solid 59-mm-diameter segment (1) and a solid…

A:

Q: A steel shaft is 250mm long. It is subjected to a transverse bending load at its free end which…

A: Step 1: Step 2: Step 3: Step 4:

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure  Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2  ×  r^2 +…

Q: A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mm has been designed to…

A: Given: Pressure = 200 Mpa To find: Radial and circumferential stress using Lame's equation Sketch…

Q: A shaft is made of an aluminum alloy having an allowable shear stress of Tallow=116 MPa. (Figure 1)…

A:

Q: The rotating stepped shaft in the figure is produced from 85080M30 steel by machining method. It…

A: Draw the free-body diagram of the beam. Apply force equilibrium in vertical direction. RA+RB=10 kN…

Q: A rotating solid circular shaft is subjected to a constant bending moment of 90 N-m and a steady…

A:

Q: Calculate the stress concentration factor (kt). the small diameter is 0.88 in and the bigger one is…

A: Given:The small diameter is the bigger diameter is The radius is The moment is The torque is

Q: yield strength of oy 750 MPa. Determine the design factor of safety using Tresca and von Mises…

A: DefinitionTersca Theory:A ductile material fails or yields when its maximum shear stress equals or…

Q: A solid shaft made of a ductile brass alloy is subjected to an array of loads, resulting in the…

A: Maximum shear stress theory Maximum shear stress theory is also known as Guest's theory. According…

Q: B BC is brass. The rod is fixed at its ends and subjected to a torque of T = 400 Nm. The steel…

A:

Q: Design a muff coupling to connect two shafts. The power to be transmitted is 27kW at a shaft speed…

A:

Q: A solid shaft is transmitting 1 MW at 250 r.p.m. Determine the diameter of the shaft if the maximum…

A: As per our guidelines we have to answer one question only so, post the question separately and…

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

A: Torque at the joint of both shaftsDiameter of the steelBecause the end reactions are same hence the…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Eigure 1)

A:

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1)…

A:

Q: Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the…

A:

Q: Time left 0:23: The driveshaft of an automobile is being designed to transmit 196 kW at 3177 rpm.…

A: Step 1: Given P=196kWN=3177rpmτall​=27MPa. Step 2: Now calculate the angular velocity of the shaft…

Q: Submit correct and complete solutions. give propriate Explanation. Provide step-by-step detailed…

A: Approach to solving the question: I carefully read the given information to understand what needs to…

Q: A stepped steel shaft, shown below, is used in a spur gear reducer. The shaft is subjected to a…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.