Section 5.1.4 Deforming Control Volume 5.30 (WILEY A hypodermic syringe (see Fig. P5.30) is used to apply a vaccine. If the plunger is moved forward at the steady rate of 20 mm/s and if vaccine leaks past the plunger at 0.1 of the volume flowrate out the needle opening, calculate the average velocity of the needle exit flow. The inside diameters of the syringe and the needle are 20 mm and 0.7 mm. Qleak Qout

Section 5.1.4 Deforming Control Volume 5.30 (WILEY A hypodermic syringe (see Fig. P5.30) is used to apply a vaccine. If the plunger is moved forward at the steady rate of 20 mm/s and if vaccine leaks past the plunger at 0.1 of the volume flowrate out the needle opening, calculate the average velocity of the needle exit flow. The inside diameters of the syringe and the needle are 20 mm and 0.7 mm. Qleak Qout

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6.23. We are offered some pipes made of a new kind of plastic. To test their roughness, we pump water through a 3-in pipe made of this material at an average velocity of 40 ft / s. The observed friction factor is 0.0032. Estimate the absolute roughness of this plastic.
3. A fire hydrant has an outlet diameter of 630 mm located 1.4 meters above the ground. If the water strikes the ground at a horizontal distance of 285 meters below the outlet, calculate the rate of discharge in gals. per min.
b) A syringe is used to deliver vaccine against an infectious disease. This particular syringe is not perfect so it is expected that 5% of the vaccine flow rate out of the needle will leak past the plunger. If the vaccine has to be injected steadily with the flow rate of 270 cm³/min, and the plunger is moving at the velocity of 600 mm/min, sketch the control volume and determine the area of the plunger.
Water flows out of 5 mm x 200 mm slots in a sprinkler as shown. The mass flow rate is 15 kg/s. 200 mm 250 mm a. Find the torque required to prevent the sprinkler from rotating. b. Find the rotation rate of the frictionless sprinkler when released.
2. A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A_1 =2 ft^2; 9_1 = 100 fpm; V_1 = 4 ft^3/lb. At section 2: A_2=2 ft^2; p_2=0.20 lb/ft^3. Calculate the speed at section 2 in ft/min or fpm %3D
1.
1.) A horizontal pipe bent reduces from 300 mm bore diameter at inlet to 150 mm diameter at outlet. The bend is swept through 50° from its initial direction. The flow rate is 0.05 m3/s and the density is 1000 kg/m³. Calculate the momentum force on the bend and resolve it into two perpendicular directions relative to the initial direction. 2.) A jet of water traveling with a velocity of 25 m/s and flow rate of 0.4 kg/s is deflected 150° from its initial direction by a stationary vane. Calculate the force on the vane acting parallel to and perpendicular to the initial direction.
Problem 4 (10 D A hydrant nozzle shown in Fig. 4 has a diameter of 100 mm at the inlet (flange). At the outlet of the hydrant, the diameter reduces to 30 mm. The fluid velocity and gage pressure at the inlet are 2 m/s and 323 KPa, respectively. The density of water is 1000 kg/m³. Neglect the weight of the pipe. Assume the flow is steady and determine: a) The jet velocity at the outlet b) The horizontal force acting on the flange PORT c) The moment acting on the flange (Point T 8 m V₂
The type of fluctuating stress in which the value of mean stress and variable stress are same and is equal to half of the maximum stress is called ____________________________. fluctuating fatigue stress repeated fatigue stress alternating fatigue stress completely reversed fatigue stress