Saturated Refrigerant-134a vapor Saturated liquid A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 3 MPa. If the fraction of the total volume occupied by vapor (Vaturate vapor/Vtotai) is 0.94 determine quality of the mixture. Present your result as percent. (For example, if you find 0.952. enter your result to system as 95.2)

Saturated Refrigerant-134a vapor Saturated liquid A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 3 MPa. If the fraction of the total volume occupied by vapor (Vaturate vapor/Vtotai) is 0.94 determine quality of the mixture. Present your result as percent. (For example, if you find 0.952. enter your result to system as 95.2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Plot the process on pv diagram which show the state points relative to the vapor dome. Label the states 1,2,3.. to indicate the sequence of the change in state.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
Saturated Refrigerant-134a vapor Saturated liquid A tank occupied by saturated liquid-vapor mixture of refrigerant-134a at 3 MPa. If the fraction of the total volume occupied by vapor (Vsaturate vapor/ Vtotal) is O.94 determine quality of the mixture. Present your result as percent. (For example, if you find 0.952, enter your result to system as 95.2)
3) A tank, well insulated, has two parts divided by partition. The first part incuded 5,5 kg of water at 600 kPa while the other part is evacuated. This partition is removed and the water expands to fill the entire tank. If the final pressure and temperature are 250 kPa and 150 °C, respectively, please determine a- The volume of the tank b- Temperature of the water for first part
Q1) 1kg saturated liquid water-vapormixture at a pressure P = 250kPa with a quality of x = 0.6 is contained in a closed rigid tank. a) Write down the temperature of the mixture. b) Now, the tank is started to be heated at constant volume with a heater of power Q = 0. 9kW until the quality of the water reaches to x = 1.0. Find the pressure of the system at this state. (when x = 1.0) c) How long does it take for the heater to bring the quality of the mixture from x = 0.6 to x = 1.0 d) Sketch by hand the temperature of the water with respect to time during the heating process.
PLS ANSWER ALL I WILL GIVE THUMBS UP
A rigid container with a volume of 2000 liters contains 4-kg mixture of saturated water and steam at 120 deg C. The mixture is slowly heated until the liquid content is completely vaporized. Determine the a) quality of the vapor at the initial condition b) temperature of water after heating
all parts plzzz(hand written asap)
Thermodynamics subject. Pleas show the complete and step by step solution. . A certain gas at 101.325kPa and 160C whose volume is 2.83m3 are compressed into a storage vessel of 0.31m3 capacity. Before admission, the storage vessel contained the gas at 137.8kPa and 240 C; after admission the pressure has increased to 1171.8kPa. What should be the final temperature of the gas in the vessel in Rankine?
T6a please help me with the answer and full solution
How much liquid water in kg is in a quality of x= 0.78, say the total mass of the liquid-vapor mixture is 50 lbm? Select one: O a 17.12 kg O b. 16.86 kg O c. 18.78 kg O d. 17.687 kg
With a volume of 200 L and a cylinder pressure of 100 kPa with the piston on the stopper a piston-cylinder assembly contains water with a degree of dryness of 50%. A pressure of 200 kPa is needed to move the piston up. Volume 400 The cylinder continues to be heated until it reaches According to this; a) This process takes into account the saturation line in the T-v and P-v diagram. show. b) Calculate the temperature in the final state. c) Find the work done. d) Find the amount of heat transfer.