Sarah wasn't sure about Ben's results, so she repeated the experiment and found the best-fit line listed below for her standard calibration curve of absorbance vs concentrationin M.y=34232 +0.0064She then prepared a solution that had 5.00 ml 0.002 Miron(1) nitrate in 1 M nitric acid, 3.00 ml. 0.002 M potassium thiocyanate, and 2.00 mL DI water.If the absorbance for the solution was 0.603, calculate the equilibrium constant. Ke with zero places after the decimalType your answer...

The molarity and volumes of reactants initially taken are: 5.00 mL of 0.002 M Fe(NO3)3 or Fe3+(aq)…

Sarah wasn't sure about Ben's results, so she repeated the experiment and found the best-fit line listed below for her standard calibration curve of absorbance vs concentration in M y-3423.2z+0.0064 She then prepared a solution that had 5.00 ml 0.002 Miron) nitrate in 1 M nitric acid. 3.00 ml 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.603, calculate the equilibrium constant, K with zero places after the decimal Type your answer..

Sarah wasn't sure about Ben's results, so she repeated the experiment and found the best-fit line listed below for her standard calibration curve of absorbance vs concentration in M y-3423.2z+0.0064 She then prepared a solution that had 5.00 ml 0.002 Miron) nitrate in 1 M nitric acid. 3.00 ml 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.603, calculate the equilibrium constant, K with zero places after the decimal Type your answer..

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The protein content of wheat flour can be determined with reasonable accuracy using the gravimetric factor 5.70+0.01. A 2.06±0.01 g sample of flour was taken through a Kjeldahl procedure and the ammonia produced was distilled into 50.0+0.1 mL of 0.1600±0.0001 M boric acid solution which required 34.7±0.1 ml of 0.174±0.002 M HCI for titration to the methy red end point. Calculate the weight percent protein [and uncertainty] in the sample. (AW Nitrogen=14.01 g/mol) *
If the absorbance for the solution was 0.698, calculate the equilibrium concentration of iron(III) thiocyanate in the solution. Report your answer in mM with three places after the decimal.
The molar absorptivity constant of a particular chemical is 2.31 M/cm. Determine the concentration of a solution made from this chemical that has an absorbance of 0.408 with a cell path length of 1.12 cm.
Chemistry
Suppose that a solution has an absorbance of 0.250 at a wavelength of 450 nm. If the concentration of the solution is 22 μM, what is the value of the molar absorptivity? The data were taken with a standard 1-cm cuvette. molar absorptivity in (L cm^−1 mol^-1):
The concentration of gadolinium was measured in the discharge from a wastewater treatment plant near a large medical facility. Eight measurements were obtained: 1.411 ppm, 1.411 ppm, 1.401 ppm, 1.409 ppm, 1.979 ppm, 1.408 ppm, 1.419 ppm, 1.402 ppm. Use the Grubbs test to determine if one of these values is an outlier. What is the value of ?cal?
4- A sample containing H2C204 had a purity equal to 90.50% (w/w). An unknown mass of this sample was dissolved in water and transferred to a 50.00 mL flask. An aliquot of 25.00 mL was transferred to an erlenmeyer flask and 50.00 mL of a 0.2000 mol L^-1 NaOH solution were added. %3 Excess NaOH was titrated with 0.09000 mol L^-1 HCI solution using 2.000 mL. Calculate the mass (g) of the sample used. Data: H = 1.008 C= 12.01 O = 16.00
15) You measure a solution that contains two organic molecules in a 1.00 cm cuvette. The measurement is 0.2265 at 700 nm and 0.9205 and 320 nm. What are the concentrations of compound A and compound B. = 3520 M'cm';e, Compound A: Compound B: e = 620 M'cm' 700m 320nm e = 13130 M'cm" ; e = 3600 M 320nm 700m 'cm'
Using the data and formula shown, Determine the concentration of iron in the sample and its standard deviation from the least-squares equation of the line. Compare the unknown concentration to that obtained manually from a calibration curve.
Hh.130.
can you explain how I can get 1.596 mg/L of concentration of Fe3+ in dilutes sample and can you also make the calibration curve.