Saitama pushes a giant rock 2000KN at the Flat it the frictional to 0.7 weighing ground is equal force and Saitama normal force. against Strength to of move coefficient Find the force How much Saitama the must apply rock

Q: When should an unacceptable work be recognized and reported to the contractor?

A: The contractor recognizes the significance of doing the work in a healthy and responsible way to…

Q: Describe phase two contracts in design work?

A: The phase two contracts are used typically when there is an opportunity for the owner to start the…

Q: Insurance, Precautionary and Safety Measures, Appointment of Building Professionals

A: Project planning and financing :  The project evaluation and budgeting process, often known as…

Q: Why is the contractor, required to submit all data through the field office and not directly to the…

A:

Q: Why is drainage clogging occur?

A: 1)Damaged Pipes-Another major cause of blocked drains is broken pipes. For water to flow freely, it…

Q: What is Environmental Management System (EMS) in the construction industry?

A: An Environmental Management System (EMS) in the construction industry refers to a structured…

Q: What are the architectural development guidelines?

A: This question is related to Building design and development from Civil Engineering. In this question…

Q: in three sentences only. 1. Guardrails 2. Cross-drains 3. Crash cushi

A: 1. Guard rail is the name for a barrier put along the edge of a highway at risky locations, usually…

Q: Explain

A: The signature and seal of an expired licensed civil engineer is not valid and acceptable. As per…

Q: What are the main contract suites?

A: The contract is a legal agreement which is signed between two or more parties. The limitation period…

Q: What are the contract modifications?

A: Contract is the agreement between two persons or two parties. one party will be a buyer or one buyer…

Q: Are the record drawings required to be prepared by the contractor?

A: On construction projects, it is common to made some changes during construction because of some…

Q: Is the Resident Project Representative responsible for ordering supplies and equipment?

A: The Resident Project Representative (RPR) person should work on full time basis whereas the engineer…

Q: Define the term Post Completion?

A: The term post-completion can be defined as the final stage of the project that comes after the…

Q: Describe the responsibilities of the inspector during construction.

A: Everyone wants a safe living and working place. For meeting these requirements of people, it is to…

Q: How does Building Information Modeling (BIM) help with pre-construction planning?

A: Approach to solving the question: To solve the question, identify and explain the key…

Q: Give a few suggestions that might be used to ensure adequate change control on projects using…

A: Change control is a way to take all the various variable things that can happen in the respective…

Q: Upon being engaged to provide resident inspection on a project, what kind of documents are needed by…

A: The inspection on a project is carried out systematically and in accordance with the details given…

Q: When do the lawyers use the Specifications?

A: Construction specifications or technical documents are a part of the construction contract. The…

Q: Identify specialty products as classified by the Construction Specifications Institute?

A: Construction specification institute(CSI) has introduced a common format for commercial construction…

Q: 4.1 The Architect as the Construction Manager (CM) is directly responsible to the Owner on all…

A: The role of the Architect as the Construction Manager (CM) is ensuring the successful execution of a…

Q: Does the error/omission lead to increased construction contractor costs?

A: An error or omission happens in the project when something lacked in finishing the building or…

Q: How many satellites in a full GPS constellation? O 30 O 12 O24 O 18

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Describe phase one contract in design work?

A: Phase One Contract in Design Work is mentioned below : Pre Design : Background Research and…

Q: Why should the  Resident Project Representative maintain a drawing log and also a shop drawing file…

A: Resident Project Representative is a person working on a project, typically on a full-time basis, to…

Q: Slab on grade Define.

A: A slab-on-grade is a type of shallow foundation in which a concrete slab rests directly on the…

Q: What are Cyclone separators?

A: A cyclone separator, also called a cyclonic dust collector, is a widely used air pollution control…

Q: What are some lumped safety factors ?

A: The use of (safe working) load capacity terminology for resistance is a convenient and easily…

Q: Describe ASTM and AASHTO Test Procedure Designations.

A: ASTM and AASHTO

Q: Cite atleast two incidents that you can gather from the internet where structural collapse or…

A:

Q: Define eskers and how it is helpful for the construction purpose?

A: Eskers:

Q: P-80 N 40 F=200 N 200 mm W=140 N 1 V3 C= 20 Nm FIGURE C 100 mm H 90 N 200 mm 400 mm 6. An angular…

A:

Q: How are curbs measured?

A: A curb is the edge where a raised sidewalk or road median meets a street or other roadway. Curb…

Q: Case study The contractor received a submittal package from the curtain wall subcontractor. Per the…

A: What should the subcontractor do with the submittals prepared by the manufacturer?The subcontractor…

Q: . Who can initiate a change order—the owner,ingineer or contractor?

A: - A change order is a type of document which includes all the changes to be incurred during…

Q: Write some of the items that are recommended by the Associated General Contractors for discussion?

A: Some of the items that are recommended by the Associated General Contractors for discussion are :…

Q: What is an RFI and how is it used?

A: The RFI is an abbreviation of Request for Information, it is a standard process whose purpose is for…

Q: Is the approval of shop drawings risky?

A: Shop drawings are the set of drawings produced by the contractor, supplier, manufacturer,…

Q: Builders Risk coverage is used to insure: a. builders completed operation b. property under…

A: Builders Risk coverage is used to insure: b. property under construction

Q: How DfMA impacts on building systems including plug and play connectors and interface

A: Design for Manufacture and Assembly (DfMA) is a way of designing and constructing a quality building…

Q: UPVOTE WILL BE GIVEN. PLEASE ANSWER IN PARAGRAPH FORM. What responsibility does an engineer have…

A: Concept- An engineer plays a crucial role in the drawings and the components that actually goes into…

Q: How are the Trailer Type field offices selected?

A: -  Trailer type field offices are type of mobile offices which can be shifted from one location to…

Q: ivate truction actor be extensiC

A: A contract is a legally binding agreement that establishes, defines, and governs the parties' mutual…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.