i need the answer quickly s+80.35zQ3: For the system of Figure 1, given G(s) = and C(z)Find the closed-loop transfer function and characteristic equation.%3Ds+5z-1R(:)E(=)U(2)Y(:)C(3)DACADCG(s)

Answered: s+8 0.35z and C(z) Q3: For the system…

s+8 0.35z and C(z) Q3: For the system of Figure 1, given G(s): Find the closed-loop transfer function and characteristic equation. %3D s+5 z-1 R(:) Y(:) U(2) DAC C(:) E(e) ADC G(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is ampere circuital law?
I need the answer as soon as possible
Question Completion Status: Click Submit to complete this assessment. Question 8 What do you do to an asynchronous counter to let it count froms14 to 0? (Handwriting solution is needed: include this in your pdf file) Click Submit to complete this asseESment,
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
The contractor is controlled by?
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.