3:03 1 Question 7 and 8 are based on this diagram. R(s) C(s) s(s + 1) 7. The block diagram has the structure of negative feedback positive feedback series parallel Clear selection 8. The transfer function C(s)/R(s) for the block diagram is (s + 1)/s 1/s2 1/(s + 1) O 1/(s? + 2s)

3:03 1 Question 7 and 8 are based on this diagram. R(s) C(s) s(s + 1) 7. The block diagram has the structure of negative feedback positive feedback series parallel Clear selection 8. The transfer function C(s)/R(s) for the block diagram is (s + 1)/s 1/s2 1/(s + 1) O 1/(s? + 2s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Transfer function. When the following feedback system gets the complex exponential signal elWt , estimate the transfer function of this system. x(t) + +) y(t) d 0.5- dt 0.1
s+10 A unity feedback system has G(s) = K s4+20s³+132s²+128s-960 a. Build the R-H table. b. Find the range of K for a stable system. C. On what frequency (in rad/s) does the system oscillate when it is marginally stable?
B-6-14. Consider the unity-feedback system whose feed- forward transfer function is G(s) F K s(s+ 1) The constant-gain locus for the system for a given value of K is defined by the following equation: K s(s + 1) = 1 Show that the constant-gain loci for 0 ≤ K ≤ ∞ may be given by [o(o + 1) + w²]²+ w² = K² Sketch the constant-gain loci for K = 1, 2, 5, 10, and 20 on the s plane.
Question1: Simplify the following block diagram. Obtain the transfer function from R to C for figure 1, and the transfer function from X(s) to Y(s) for figure 2. Question 2: Convert the block diagram of figures I and figure 2 to a signal-flow graph. G R G2 G3 G3 G4 G6 Figure 1: Block Diagram input output Y(s) X(s) 2 Figure 2: Block Diagram
2. For the unity feedback system of Figure determine the range of K to ensure stability G(s) = K(s + 6) s(s+ 1)(s+4) I
Q2: Answer A or B A: Simplify the block diagram shown below and obtain the closed-loop transfer function C(s)/R(s). G₁ R(s) C(s) G₂ H₁ H₂
For a system with a DC gain of 2 and open-loop poles S1,2= -3+ or - j4 What is the transfer function. I need a step by step answer please :)
Q\ Solve the following questions while giving the reason for each point 25. Each RC circuit in an op-amp (a) causes the gain to roll off at -6 dB/octave (b) causes the gain to roll off at-20 dB/decade (c) reduces the midrange gain by 3 dB (d) answers (a) and (b) 26. If a certain op-amp has a midrange open-loop gain of 200,000 and a unity-gain frequency of 5 MHz, the gain-bandwidth product is (a) 200,000 Hz (b) 5,000,000 Hz. (c) 1 x 1012 Hz (d) not determinable from the information 27. The bandwidth of an ac amplifier having a lower critical frequency of 1 kHz and an upper critical frequency of 10 kHz is (a) 1 kHz (b) 9 kHz (c) 10 kHz (d) 11 kHz 28. The bandwidth of a de amplifier having an upper critical frequency of 100 kHz is (a) 100 kHz (b) unknown (c) infinity (d) 0 kHz 29. When negative feedback is used, the gain-bandwidth product of an op-amp (a) increases (b) decreases (c) stays the same (d) fluctuates 30. If a certain op-amp has a closed-loop gain of 20 and an upper critical…
(b) Block diagram of a system with unity feedback is illustrated as R(s) Y(s) K G(s) Figure Q3(b) and the transfer function is given as 50000 G(s) = s² + 150s + 5000 From the given block diagram and transfer function, sketch an approximate magnitude and phase of Bode Plot. Choose any value of K that you might think will simplify your sketching. There is no requirement of K value in this sketching process. The selection of Kis only necessary if you have a particular design requirement.
Q1) A closed loop system is shown below the input is R(s) and the output is Y(s) (s + 1) (s + 4) 1 1 (s – 3) Y(s) a) Determine the closed loop transfer function R(s) b) Derive the equivalent state space model c) Hence from the state space model Sketch a block diagram model for the system
(IV) A specialist sensor is being used to detect the pollution being emitted from an engine. The true signal is in the range of 30-50mV DC but is being affected by 800HZ AC noise from the electronic engine controller. Design a modular system consisting of a filter (that removes the noise) and an op-amp based amplifier (that increases the signal to a range of 3-5V DC) (V) The op-amp used in part (iv) above has an open-loop (i.e. without feedback) gain-frequency graph as shown below. 100000 10000 1000 100 10 1 10 100 1000 10000 100000 1000000 10000000 Frequency (H2) Voltage Gain, Av (Vout/Vin)
3. In this problem, use the two closed loop systems given in the figure to answer the questions below. 4 R(s) K₁ 0.0099 In thin K₂ Y(s) R(s) K₁ 4 S(s) = 0.09 K₂ 0.09 (a) Show that these two systems have the same transfer function for K₁ = K₂ = 100 (b) Using the definition of sensitivity, S(s), for each system calculate the sensitivity to the parameter K₁ with K₁ and K₂ as variables. Recall: Y(s) OG G OG Gal (c) Substitute K₁ = K₂ = 100 into each S(s) and compare the sensitivities to parameter K₁.