Draw the signal flow graph of the following diagram. R is the input and C is the s² output. Blocks are represented by the following functions: G(s) = and (S³+2) H(s) = 5. Using Mason's formula, express the closed-loop transfer function. You must indicate the paths, loops, path gains, loop gains, touching/non-touching loops, cofactors and delta explicitly. R E G H

Draw the signal flow graph of the following diagram. R is the input and C is the s² output. Blocks are represented by the following functions: G(s) = and (S³+2) H(s) = 5. Using Mason's formula, express the closed-loop transfer function. You must indicate the paths, loops, path gains, loop gains, touching/non-touching loops, cofactors and delta explicitly. R E G H

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need answer within 20 minutes please please with my best wishes
Please click on pic to open it
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • An abc-phase sequence three-phase balanced wye-connected source supplies power to a balanced delta-connected load. The impedance per phase in the load is 14+j12 Ω. If the source voltage for a phase is Van=120<80° Vms, and the line impedance is zero, find the phase currents in the wye-connected source.
Don't need to explain, but please answer all the question. 1. The resistance strain gauge can measure plastic deformation. A) True B) False 2. In order to save cost, the resistance strain gauge can be reused. A) True B) False 3. In the quarter bridge, there is only one strain gauge which resistance value will change. A) True B) False 4. The shell of inertial acceleration sensor is fixed on the measured object. A) True B) False
What is shop drawings, why we use them? I
Discuss and explain what is Voltage Multiplier?
Answer question clearly and fully. Make sure I can properly read out the steps. Include any and all equations used during the solving process.
DEGREE: Electrical Engineering SUBJECT/COURSE: AC CircuitsTOPIC: Converter and Rectifier NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. REQUIRED/FIND/MISSING (with symbol/s)4. ILLUSTRATION (Required).5. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: A 1,000-kw three-phase converter delivers full load at 600volts. If the efficiency is 94percent and the power factor is 0.96, determine:(a) the direct-current output(b) the a-c slip-ring current(c) the kilovolt-ampere load delivered by each transformer.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: TRANSFORMERS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:Connect the three 1-Φ transformers in bank:Primary winding in WYE and secondary windings in DELTA.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. REQUIRED/FIND/MISSING (with symbol/s and units)4. ILLUSTRATIONS such as diagrams and graphs are Required5. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible6. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:A 6.6 kV, star-connected,3-phase, synchronous motor works at constant voltage and constant excitation. Its synchronous impedance is (2.0 + j 20) per phase. When the input is 1100 kW, its power factor is 0.8 leading. Find the power factor when the input is increased to 1800 kW.
DEGREE: Electrical Engineering SUBJECT/COURSE: AC CircuitsTOPIC: Converter and Rectifier NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. REQUIRED/FIND/MISSING (with symbol/s)4. ILLUSTRATION (Required).5. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM:A six-pole three-phase wound-rotor motor is to be used as an induction frequency converter. The stator is connected to a 60-cycle source. At what speed, and in what direction, must the rotor be driven if it is to develop:(a) 120 cycles?(b) 100 cycles and 180 cycles?(c) 40 cycles?