RS-9. The 8-mm-diameter bolt is made of an aluminumalloy. It fits through a magnesium sleeve that has an innerdiameter of 12 mm and an outer diameter of 20 mm. If theoriginal lengths of the bolt and sleeve are 80 mm and50 mm, respectively, determine the strains in the sleeve andthe bolt if the nut on the bolt is tightened so that the tensionin the bolt is 8 kN. Assume the material at A is rigid.E - 70 GPa, Emg - 45 GPa.50 mm-30 mm

Given data: The inner diameter of the bolt is di=12 mm. The outer diameter of the bolt is d0=20 mm.…

Answered: RS-9. The 8-mm-diameter bolt is made of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket F₁ Answers: Tpin B = i Ob = i a B MPa MPa
The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for each gage: Pa = -200(10-6), Pb = 300(10-6), and Pc = 250(10-6). Determine the in-plane principal strains.
315-003 F21 E 31 Load P is applied at point B of the frame seen below forcing point B to move 2.0 mm to the right. Determine the normal strains in members AB and BC in microns. (9 points) 2.0 m 1.5 m
Mechanics of deformable bodies
The rods A and B having a tensile stress of 400 N/mm², determine the diameter so that they can support the load shown. Then calculate the change in length and strain in each bar if (E=200000 MPa) (L=2 m)
The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 26 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 120 MPa, the punching shear stress in the support plate cannot exceed 110 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Rod Answer: Pmax i Hole diameter D Head KN d a
Tube with 100 mm long and 20 mm diameter. If the axial load is 300ON is applied to it. Determine the stress and .strain if change in length AL=D0.5mm 3000 N d=20 mm L=100 mm 3000 N
1. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Material parameters are Ep = 2.70 GPa and vp = 0.4. 300 N 200 mm 300 N
The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 28 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate - Hole diameter D Rod Нead b -
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 270mm, b = 150mm, c = 70mm, and 0= 50°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 39 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket F₁ Answers: Ob Tpin B = Bell crank Bu CI B MPa MPa F₂
If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can be applied to the bar. P 40 mm 5 mm 20 mm r = 10 mm 20 mm P
The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a diameter of 13 mm and the steel pins at A, B and C have a diameter of 10 mm. The yield stress of the steel in tension is 250 MPa and in shear is 125 MPa. C 1.2 m 0.9 m 0.3 m Determine the factor of safety for the pin at B with respect to yielding? Input your answer to two decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS