1. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Material parameters are Ep = 2.70 GPa and Vp = 0.4.

1. The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Material parameters are Ep = 2.70 GPa and Vp = 0.4.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.11P: A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the...

See similar textbooks

Related questions

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: Determine the change in length, width and thickness of steel bar which is 4m long, 30mm wide and…

A: The change in the length of the steel bar can be calculated as shown below. P: Load L: Length of…

Q: Find the breaking point along the fishing rod assuming that the base of the rod is in a fixed…

A: Given: Diameters of the rods are: a = 9.93 mm b = 7.13 mm c = 5.1 mm Total length of the rod is 2 m.…

Q: 4. Calculate the Youngs modulus for the materialL of the bar shown below, The bar has an initial…

Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter…

A: Given: Tensile load P=40 KN Diameter of the rod D=40 mm Area of the road A=π4D2…

Q: ft, the 6-meter-high arm is manufactured using the l profile given below. It is fixed to both ends…

Q: 12. A column of length 18" and a diameter of 0.25" was tested with both ends pinned. The measured…

A: Given- Length (L) = 18 inch Diameter (d) = 0.25 inch E = 29000 ksi = 29000000 lbs/in2 Case 1 -…

Q: A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter. The column…

A: Givenhollow columnone end is hinged and the other end fixed.t=5mm=0.005mD=60mm=0.060mL=1.2mE=206…

Q: a steel column that has a diameter of 50mm and 32m long is surrounded by an iron shell that is 5mm…

Q: The timber member has a cross-sectional area of 1750 mm? and its modulus of elasticity is 12 GPa.…

Q: Problem 2 A cylindrical specimen of a nickel alloy hav- ing an elastic modulus of 207 GPa (30 x 106…

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The…

Q: A steel rod having a length of 1m has a cross-sectional area of 100mm^2. if it is subjected to an…

Q: If load P = 20.3 kips, determine the normal force in bar (1). D A 6 ft 43.8 kips 31.0 kips 33.8 kips…

Q: A bar made of a space age polymer has the stress-strain curve shown below. If the bar has a length…

A: Given:The length of the bar is The cross-section of the bar is The axial load is The equation of the…

Q: A tensile load of 20 kN is applied on a wire made of a copper alloy having an elastic modulus of 120…

Q: At the proportional limit, a 20-mm-thick x 75-mm-wide bar elongates 7.2 mm under an axial load of…

A: Given : t = 20mm w = 75 mm change in length (elongation) δL = 7.2 mm P = 470 kN = 470000 N L = 1.6…

Q: A bracket is supported by means of 4 rivets of the same size. Design the diameter of the rivet if C,…

Q: 3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive…

Q: A hollow cylindrical rod with a diameter of mm and a thickness of mm is under a tensile load of…

Q: The steel strip has a uniform thickness of 50 mm. Compute the elongation of the strip caused by the…

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

Q: A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it,…

A: Given data, L= 200 mm D= 15 mm F= 300 N E= 2.7 GPa Poison ratio v= 0.4

Q: A cylindrical metal rod of 20mm diameter and 1m length is subjected to a tensile load of 60KN. To…

Q: Question 2 A rod, which tapers uniformly from 40 mm diameter to 20 mm diameter in a length of 400 mm…

Q: A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of…

A: Given data: The length of the bar, L = 200 mm. The cross-section area of the bar, A = 7500 mm2.…

Q: Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength…

A: Consider the diagram as show below for the arm.

Q: The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m…

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN.…

Q: A uniform edge load of w1 = 530 lb/in. and w2 = 320 lb/in. is applied to the polystyrene specimen.…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is…

Q: A uniform edge load of 500 lb>in. and 350 lb>in. is applied to the polystyrene specimen. If…

A: To find The new dimension of a', b', t'. Given The length a is 2 in. The length b is 2 in. The…

Q: A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: The tensile force is F=100 kN. The initial diameter of the rod is di=0.02 m. The initial length of…

Q: 300 N 200 mm 300 N

Question

1. The acrylic plastic rod is 200 mm long and 15 mm in
diameter. If an axial load of 300 N is applied to it, determine
the change in its length and the change in its diameter.
Material parameters are Ep = 2.70 GPa and vp = 0.4.
300 N
200 mm
300 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 1 A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter 20 mm is made centrally on the rod. To what length the rod should be bored so that the total extension will increase 30% under the same tensile load. Take E = 2 x 10$ N/mm2.
A plastic rod is 200mm long and 15mm in diameter. If a tensile load of 300N is applied to it, determine the change in its length and the change in its diameter. Assume Modulus of elasticity (E) = 2.70 GPa, and poisson's ratio (v) = 0.4. indicate free body diagram
Need asap A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. If μ = 0.33 and E = 105 GPa. Determine the change in diameter. In mm. Thanks
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
A bracket is supported by means of 4 rivets of the same size. Design the diameter of the rivet if C, (tensile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20N 20kN 30 nm so nm 30 mm 1.
A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 260 kN without exceeding an allowable stress of 240 MPa or stretching more than 10 mm.
At the proportional limit, a 20-mm-thick x 75-mm-wide bar elongates 7.2 mm under an axial load of 470 kN. The bar is 1.6-m long. If Poisson's ratio is 0.32 for the material, determine the modulus of elasticity. O 69.6 GPa O 58.3 GPa EEA O 76.2 GPa O 44.7 GPa 48.9 GPa
Required information The specimen shown has been cut from a 5-mm-thick sheet of vinyl (E= 3.10 GPa) and is subjected to a 1.5-kN tensile load. It is given that /= 70 mm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Dimensions in mm A B 10 C P' = 1.5 kN P = 1.5 kN 25 25 40 40 Determine the total deformation of the specimen. The total deformation of the specimen is mm.
Parvinbhai
Don't waste my question please, thank you god bless. I will vote it up if you give the solution.
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?
#3