rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with Esteel = 210 GPa. Rod B has a diameter of 16 mm and is made from copper with Ecopper = 105 GPa. This simply supported beam is to carry a motor vehicle engine and gearbox weighing 5,5 kN. 5.1 Determine the distance 'x' from the left-hand support 'A' in order for the beam to remain in a horizontal position. (7/ /4/ 5.2 Calculate the stress in each rod due to the applied load. /2/ 5.3 Calculate the movement (extension) of the support wires under this 5.5 kN load. 5.4 Will the rods be able to withstand the applied load? Motivate your answer. /2/ 500 mm 300 mm x A 5.5 KN 1500 mm B

rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with Esteel = 210 GPa. Rod B has a diameter of 16 mm and is made from copper with Ecopper = 105 GPa. This simply supported beam is to carry a motor vehicle engine and gearbox weighing 5,5 kN. 5.1 Determine the distance 'x' from the left-hand support 'A' in order for the beam to remain in a horizontal position. (7/ /4/ 5.2 Calculate the stress in each rod due to the applied load. /2/ 5.3 Calculate the movement (extension) of the support wires under this 5.5 kN load. 5.4 Will the rods be able to withstand the applied load? Motivate your answer. /2/ 500 mm 300 mm x A 5.5 KN 1500 mm B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the given figure, support A is a roller and support B is a pin support. If P=15 kips, calculate the 1) vertical reaction at A, 2) vertical reaction at B, 3) horizontal reaction at B P 6 kips 6 kips В 6 ft – 3 ft 2 ft ' 2 ft
For the beam shown, use only singularity functions. V₁ = 45 lbf/in and V/₂ = 5 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 0 1400 lbf Hinge JA B₁ C R₂ R₁ 4 in 4 in 2 in V1 V2 D R₂ + What is the value of the peak moment between points Cand D? The peak moment between points C and Dis Ibf.in.
Hi, I want to find the location on the beam where the maximum bending moment happens as measured from point A. I have already gathered the following information. FAx= 0 FAy= 25.0869 FCy= 32.913 the sheer force at B= 3.087 The bending moment at B = 77.4785 Let the loading coefficents be: W1 = 4 kN/m, W2 = 8 kN/m Let the lengths be: L1 = 5.5m , L2 = 6m. If anyone could help me with this last step of the problem that would be great.
The built-up beam is subjected to a moment of M = 80 kNm. Variable d₁ d₂ d3 da Values for the figure are given in the following table. Note the figure may not be to scale. d5 d3 de d₁ Value 128 mm 22 mm 276 mm 11 mm 138 mm d4 12 mm M₁ de d5 a. Determine the distance from the Neutral Axis to the top of the beam, N.A. b. Determine the mass moment of inertia of the beam, I. Determine the max compressive stress acting on the beam, compression c. d. Determine the max tensile stress acting on the beam, tension.
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 1) Draw the bending moment diagrams of shaft AD for My and M₂, and indicate the location and the magnitude of the maximum bending moments. 10 in 200 lbf 1000 lbf 10 in 500 lbf 100 lbf 10 in F G E
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
A simply supported beam (pin at one point and roller at the other) is 10 ft. long and supported at the ends. It is subjected to a uniform load of 100 lbf/ft. The rectangular beam is 1.5" wide and 9.25" tall. What is the maximum tension in the beam? 72 psi 61 psi 52 psi 81 psi
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support (triangle)? 3 ft Y-direction for the pinned support (triangle)? 2 ft For the beam above, what are the support reaction forces? Please report your answers in the units of 'kips' and to 2 significant digits (i.e. two decimal places). 6 in 9 in