A beam is partially loaded with a2 kN2 kN/muniform load of 2 kN/m and a point load of 2 kN asshown below.ALLBi.Determine the support reaction forces.Draw the Shear Force Diagram usinganalytical equations.Draw the Bending Moment Diagram usinganalytical equations.Assume beam has a square cross section, dimension the beam cross section as maximumallowable bending stress is given Gall-50 MPai.3 m2 miii.iv.

Answered: Image /qna-images/answer/03d1cc72-220d-4304-a59d-12babbde8e9c.jpg

2 kN 2 kN/m uniform load of 2 kN/m and a point load of 2 kN as shown below. B i. Determine the support reaction forces. ii. Draw the Shear Force Diagram using analytical equations. 3 m 2 m Draw the Bending Moment Diagram using analytical equations. Assume beam has a square cross section, dimension the beam cross section as maximum allowable bending stress is given Gall=50 MPa iii. iv.

2 kN 2 kN/m uniform load of 2 kN/m and a point load of 2 kN as shown below. B i. Determine the support reaction forces. ii. Draw the Shear Force Diagram using analytical equations. 3 m 2 m Draw the Bending Moment Diagram using analytical equations. Assume beam has a square cross section, dimension the beam cross section as maximum allowable bending stress is given Gall=50 MPa iii. iv.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.9P: A simple beam with an overhang supports a uniform load of intensity q = 1200 lb/ft and a...

See similar textbooks

Similar questions

-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A heavy object of weight W is dropped onto the midpoint of a simple beam AB from a height h (see figure). Obtain a formula for the maximum bending stress ^ma* due to tne filing weight in terms of h, st, and 5st, where it is the maximum bending stress and Sstis the deflection at the midpoint when the weight W acts on the beam as a statically applied load. Plot a graph of the ratio o"max/ö"it (that is, the ratio of the dynamic stress to the static stress) versus the ratio iifS^r(Let h/S^ vary from 0 to 10.)
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A simple beam with an overhang supports a uniform load of intensity q = 1200 lb/ft and a concentrated P = 3000 lb load at 8 ft to the right of A and also at C (sec figure). The uniform load includes an allowance for the weight of the beam. The allowable stresses in bending and shear are 18 ksi and 11 ksi. respectively. Select from Table F-2(a), Appendix F, the lightest I-beam (S shape) that will support the given loads. Hint: Select a beam based upon the bending stress and then calculate the maximum shear stress. If the beam is overstressed in shear, select a heavier beam and repeat.
A beam is partially loaded with a uniform load of 2 kN/m and a point load of 2 kN as 2 kN 2 kN/m shown below. A B i. Determine the support reaction forces. Draw the Shear Force Diagram using analytical equations. Draw the Bending Moment Diagram using analytical equations. iv. ii. 3 m 2 m iii. Assume beam has a square cross section, dimension the beam cross section as maximum allowable bending stress is given Oall=50 MPa
3 moment equation for this problem
strenght of materials problems
PLS ANSWER ASAP, WILL UPVOTE FOR SURE
1. Find the maximum bending stress - and find the factor of safety 2. find with using the general hear formula - shear stress - and find the factor of saefty
question in picture
Calculate the support reaction at A and B for thve beam shown in the fiqure below Take F 700 N. 3M 1M By Reaction force at point B By UN. Reaction force at point A N. Ay=