Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection 8, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m B 6 mm - 0.7 m- 0.4 m

Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection 8, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m B 6 mm - 0.7 m- 0.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A prismatic beam (as shown below) has plastic moment capacity of Mp, then the collapse load Pof the beam is P P/2 L/2 – - L/2 + L/3
Measure the width of the web of the cross- section of the cross-section of the T-beam in the figure with millimeter accuracy, when the yield strength of the aluminum material of the beam is 280 MPa and n = 1.5 is desired for the reliability. The width of the beam flange is 50 mm and the height is 14 mm, while the height of the web is 39 mm. The beam is loaded with a point force F = 3 kN and a distributed force q = 6 kN / m, and its dimensions are a = 0.6 m, b %3D = 0.5 m and c = 0.5 m. %3D Absolute value of bending torque Max = ? kNm Width of the web (integer) = ? mm
Q3
PLEASE PROVIDE COMPLETE SOLUTION THANKS
Instruction: Use 3 decimal places.
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
help me solve this in 30 mins pls
Q4 (b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.
(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm