Rigid horizontal bar AD is loaded at D and pin connected at A. Pin connected bars (1) and (2) also support AD. Determine the force in (1) and (2) and the deflection of D. E, = 70 GPa L, = 500 mm A, = 420 mm² Az= 320 mm? (2) L, = 700 mm (1) E, = 105 GPa rigid bar B C P=36 kN 380 mm 380 mm 760 mm

Rigid horizontal bar AD is loaded at D and pin connected at A. Pin connected bars (1) and (2) also support AD. Determine the force in (1) and (2) and the deflection of D. E, = 70 GPa L, = 500 mm A, = 420 mm² Az= 320 mm? (2) L, = 700 mm (1) E, = 105 GPa rigid bar B C P=36 kN 380 mm 380 mm 760 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) Determine the moment of the force about point 0. Neglect the thickness of the member. 50N H00mm 45 200 mm -100 mm-
A. Explain briefly what you understand by the following terms I) strut II) column B. Distinguish between long and short column C)a hollow alloy 5000mm long with external and internal diameter of 50mm and 25mm respectively is used as a column with one end fixed and the other end hinged.Determine the buckling load by Euler's formula.Take Young modulus of elasticity as 180GN/m^2.
Please don't provide handwritten solution ...
What is the magnitude of the maximum deflection (mm to 1 decimal place) of an aluminum diving board with h - 35 mm and b =350 mm with a person of mass 100 kg standing at the end. L = 2050 mm, L1 = 725 mm, E = 71.7 GPa (b) Cantilevered diving board Your Answer: h Answer E
Please any one can help me with finding the acting force on member BC and DE and the deflection at point A
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
QUESTION 2 An aluminium rod ABCD showa in Figure 2 is rigidly sapported at D and loaded at A and B. The total length of the rod is L=900 mm. Given that P=4 KN and Young's Modulus, Eu = 70 a By taking segmeat BCD as a solid member, desermine the magninade of Q such that the deflection at poim Ais zer b) Q = 10 KN and the deflection of point A is limited to 005 mm, what is the matimum allowahle diameter da far segmemt CD, if this segment is ow holow? L/3 Segment AB Diameter di = 20 mm Sepmem BC L3 Diameter de 0 mm Segmem CD Diameter da (uner) - 0 mm L/3 Dianeter di (inneri D Figure 2 Drawing not te sale
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
A frame supported by pins A and C is made up with bar AB and L-bar BC connected by pin B. It is loaded by a 72 Nm moment at the midpoint D of bar AB, an 18 N concentrated load at joint B, and a 6 N/m distributed loading, as shown. Clearly show ALL FBDS used. 0.4m 0.8m 18 N 72 Nm 0.6m 6 N/m A Determine the following: a. The reactions at support A (include directions in your final solutions) Ag |N Ay N b. The reactions at support C (include directions in your final solutions) N Cy N
An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 725 mm² and an elastic modulus of 26 GPa. Bar (2) has a cross-sectional area of 1610 mm² and an elastic modulus of 16.0 GPa. Determine the deflection of point A relative to support C. 70 kN A 0.85 m -2.030 mm -1.754 mm -1.275 mm -1.656 mm O -2.420 mm 90 kN (1) 90 kN B (2) 1.15 m