Ricky has a sedimentary rock sample witha specific gravity of 2.68. Based on thetable, we can infer that the rockclassification is most likelyTable 13.35 Typical specific gravity values for rock types in Queensland(Main Roads, 1989).Rock typeNameSpecific gravityIgneous- AcidAdameliteDacite2.62GraniteGaranidiorite2.642.612.70RhyoliteTuff2.612.56-2.82- Basic2.80-3.002.872.902.832.682.62BasaltDioriteGabbro- IntermediateDoleriteTrachyandesiteTrachyteMetamorphicAmphibioteGreenstone3.042.972.67-3.132.722.65HornfelsMetagreywackeQuartziteSlate2.70Sedimentary andduricrustDolomiteLimestoneMudstone2.742.682.63

In the sedimentary rock type we will check for specific gravity.

Answered: Ricky has a sedimentary rock sample…

Ricky has a sedimentary rock sample with a specific gravity of 2.68. Based on the table, we can infer that the rock classification is most likely

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A parameter m in the Hoek-Brown criterion indicates how the type of rock affects the criterion's strength. It is anticipated that the rock will be stronger with a greater value of m. Using the values of m provided in the question and comparing the peak compressive strengths of granite, rhyolite, and marble with each other, qu = 100MPa For marble (m = 7): peak compressive strength =? For rhyolite (m =17): peak compressive strength =? For granite (m = 25): peak compressive strength =?
Homework 1: a sample of rock has a total mass of 300 gm and a dry mass of 250 gm with a real specific weight of 2.77 and a degree of saturation of 80%. Find the following: Total volume, volume of solid particles, volume of voids, total density, dry density, void ratio, porosity, moisture content. Ans: V=152.75 cm³, V-90.25 cm³, V, 62.5 cm³, y-1.964 gm/ cm³, Ya 1. 64 gm/ cm³, e-0.693, n-0.41, and 6-0.2 ]
What are the six parameters of the RMR of a rock mass?
Attempt 10 The weight percent of silicon in six different rock samples, each containing different amounts of silicon, was measured different methods. The results are given in the table. two Sample Method A Si wt% Method B Si wt% 1 11.570 11.550 2 15.380 15.290 3 17.950 17.830 4 22.840 22.810 5 25.110 25.170 6 27.070 27.030 Determine feale- 0.300 feale Incorrect Determine fuable at the 95% confidence level. A list of r values can be found in the Student's r table.
A rock with 4% water absorption by weight has a dry weight of 656 g, a degree of saturation of 27%, Its weight in water is 415.45 g and its specific gravity is 2.72. This rock; a) Apparent and total porosity b) Natural and grain unit volume weight c) water content calculate.
1) A dry rock weighs 240 grams and has a bulk density of 2.5 grams per cubic centimeter. Whensaturated with pure water at room temperature (T = 25 °C), it weighs 255 grams. At room temperature,specific volume of water is 1.00295E-03 m3/kg. Calculate the porosity of the sample. 2) A cylindrical core sample of 1.5 cm length and 1.2 cm2cross-section has upstream and downstreampressures of 2 atm and 1.25 atm, respectively, during steady state flow of water at 1.00 g/s at roomtemperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm3).
There are 2 samples of granite rock from similar sampling site. However, its dimension height and diameter are different, i.e. for sample A is 104mm : 52mm (height : diameter) and sample B 52mm : 52mm. Between sample A and B, which is expected give a higher rock strength. Justify your answer?
Given the following lab data, calculate the pore volume compressibility for a sandstone sample at 4,000 and 6,000 psi. Pore volume of the sandstone sample is 50 cm3. Pressure, psi Vol. fluid expelled, cm3 1000 0.244 2000 0.324 3000 0.392 4000 0.448 5000 0.5 6000 0.546 7000 0.596 8000 0.63
we were told that the sigma y going up the sign is supposed to be negative in rock mechanics. ( I am confused, can you explain please) and the formula given to us about txy' does have a negative sign. I try it before posting those questions to verify my answer but because of those sign answer are different.
A consolidated-undrained test was conducted on a normally consolidated clay sample. The results are as follows: Undrained angle of friction = 38.65°, Drained angle of friction = 62.59°, Deviator stress at failure = 509 lb/ft^2. Determine the pore water stress at failure in lb/ft^2.
A reservoir-rock sample has a porosity of 0. 18 measured at 14.7 psis. The rock compressibility is0.77 X 10 5psi *.What would the rock porosity be at 2,000 and at 3,000 psis? Plot the relationship be tween ¢ and p in a pressure range of 14.7 to 5,000 psis
In a triaxial shear test of cohesionless soil, the soil cylinder was subjected to a liquid pressure of 16kPa inside the chamber. It was observed that failure of the sample in shear occurred when the axial compressive stress reached 40kPa. What is the nearest value of the internal angle friction in degrees of the soil sample? A. 25.4 B. 26.8 C. 29.1 D. 27.4