RI0-2. The shaft is made of A992 steel and has an alkowable shear stress of To - 75 MPa. when the shaft is rotating at 300 rpm, the motor supplies 8 kW af power, while gears A and B withdraw 5 kW and 3 kW, respectively. If the angle of twist of gear A relative to C is not alkowed to exceed 003 rad, determine the required minimum diameter of the shaft to the nearest millimeter. 300 mm S00

Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…

A:

Q: A static shaft is subjected to torques at A, B, and C. It has a diameter of 58 mm and is made from…

A: The magnitude of angle of twist is The length of shaft  1 is The length of shaft 2 is The diameter…

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: The shaft is made of A-36 steel, has a diameter of 95 mm, and is fixed at B while A is loose and can…

A: Write the given data.

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: The splined ends and gears attached to the A992 steel shaft are subjected to the torques. The shaft…

A: Diameter of the shaft (D)= 50 mmFor the A992 steel shaftthe value of the shear modulus is G=75Gpa

Q: The 60-mm-diameter shaft is made of 2014-T6 aluminum (G=27 GPa). If the allowable stress is Tallow =…

A:

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A…

A:

Q: The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM.  The shaft is…

A: Given, Total power being transmitted = P = 65 hp = 4.29 x 105 lbf-in/s Rotational speed of shaft = N…

Q: The torque of 250 kN.m produces a maximum shear stress of 48 MPa in the 8 m-long hollow steel shaft.…

A:

Q: The 63-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure Part A If the allowable…

A: Givend=60mmτallow=80MPaθA/Callow=0.060 rad

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: The diameter of the shaft DF is The power at F is The power at A is The power at B is The power at C…

Q: If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa,…

A: allowable stress = 20 Mpa  Length = 0.75 m  Modulus of rigidity G =37 GPa

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

A:

Q: The 45-mm-diameter A992 steel shaft is subjected to the torques shown where T = 760 N.m. - Part A…

A:

Q: The composite shaft consists of a mid-section that includes the 1-in. diameter solid shaft and a…

A:

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.