I Review | ConstantsWater flows from the pipe shown in the figure with a speedof 2.0 m/s. (Figure 1)Part AWhat is the water pressure as it exits into the air?Express your answer to two significant figures and include the appropriate units.Figure1 of 1μΑ?Openp =ValueUnits5.0 cm?SubmitRequest Answer4.0 mPart B10 cm? I Review | Constantsp =vUlueUniisWater flows from the pipe shown in the figure with a speedof 2.0 m/s. (Figure 1)SubmitRequest AnswerPart BFigure1 of 1What is the height h of the standing column of water?Express your answer to two significant figures and include the appropriate units.ОpenHA5.0 cm?h =ValueUnits4.0 mSubmitRequest Answer10 cm?

water flows in pipe arrangement as shown in the figure Speed = 2m/s Assuming the atmospheric…

Review | ons Water flows from the pipe shown in the figure with a speed of 2.0 m/s. (Figure 1) Part A What is the water pressure as it exits into the air? Express your answer to two significant figures and include the appropriate units. Figure < 1 of 1 > HÀ ? Open Value Units 5.0 cm Submit Request Answer 4.0 m Part B

Review | ons Water flows from the pipe shown in the figure with a speed of 2.0 m/s. (Figure 1) Part A What is the water pressure as it exits into the air? Express your answer to two significant figures and include the appropriate units. Figure < 1 of 1 > HÀ ? Open Value Units 5.0 cm Submit Request Answer 4.0 m Part B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explain operating principles for Menard-type pressuremeter.
Water moves at around 15 feet per second through a 2 ft in diameter steel pipe. Could the capacity be enhanced by inserting a smooth plastic pipe with a roughness of 0.0003 ft?Is there a liner that reduces the internal diameter to 1.9 feet? Compute the change in capacity for a fixed pressure drop and the change in pressure drop for the same flow.
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
The figure below shows a fabricated assembly made from three different sizes of standard steel tubing listed in Appendix G.2. The larger tube on the left carries 0.075 m3/s of water. The tee branches into two smaller sections as shown. Reducing tee Flow 100-mm OD x 3.5-mm wall steel tube - 160-mm OD x 5.5-mm wall steel tube - 50-mm OD x 1.5-mm wall steel tube Required If the velocity in the 50-mm tube is 10.00 m/s, what is the velocity in the 100-mm tube to the nearest 1000th?
Exercise#3: The figure shows a system. The system is conservative energy between the two valves CV, and CV2. The differential pressure element at point 1 shows a reading for flow rate. This flow rate is equivalent to AP = 3 mmH20 with k factor of orifice equals 20 m² (used as dimension geometry for the pipe). Another turbine flow meter at point 4 shows a reading for flow rate equals 2.7. Based on the reading of the first flow meter, is the turbine flow meter give the correct reading or not? You can utilize the following given information: diameters at point1&2 are D, = D2 = 0.2 m, Dz = D4 = 2 D2, Q1= 3Q2, P4 = P3 – 200000 Pa ,p = 750 Total heads(or energy)of Bernoulli equation at point 1=Total heads(or energy)of Bernoulli equation at point 2+4m, and point2 point1 Total heads(or energy) of Bernoulli equation at point 3=Total heads(or energy) of Bernoulli equation at point 4+10m. CV, 8 Closed DP · Flow meter h tank Turbine Flowmeter CV2 voint4 point3
SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER Calculate the density, specific weight, and volume of chloride gas at 25 °C and pressure of 600 000 N/m^2 absolute.
. A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 8.930 feet. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in2 in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, water = 62.4 lb/ft3 ) a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
please solve in 40 mins i need help i will give you positive feedback
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
Given A pipe is tapered to form a nozzle as shown in the figure, and the nozzle produces a jet velocity of 102 ft/s. 1.0-in diameter Flow 0.75-in diameter Required Calculate the required pressure in the larger section to produce the jet velocity given, in psi to the nearest 10th. The fluid is water at 180°F (Appendix A). Your Answer:
Any help will be appreciated