Review: Design of simple structures 1. "1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. - 1500 lb 2 ft 4 ft- 1500 lb B 60°

Review: Design of simple structures 1. "1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. - 1500 lb 2 ft 4 ft- 1500 lb B 60°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the steel structure shown, a 6-mm-diameter pin is used at C and 10- mm-diameter pins are used at…

A: Determine Vertical Displacement of point A in mm

Q: Find the stresses in members BC BD and CF for the truss shown. Indicate the tension or compression.…

A: We will use method of joints

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: To find force in member BE, CE

Q: For the truss shown, determine the normal stress of member AE, FB and CD. Identify if the stress is…

A: For the truss given below, the normal stress of member AE, FB, and CD are to be determined.

Q: 4.yielding of the web represents one of the a) shear limit state) .b) moment limit state)…

A: The correct answer is option a) Shear limit statea) Shear limit state:A limit state in beam design…

Q: Trusses 1. Find the stresses of FAB, FAC, FBC & FBD- ( 20k 15k 60 60 Ra Rb

A: This question belongs to subject structural analysis. In this question find out stresses in members…

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

Q: A B 400 mm 500 mm 20 mm 40 mm 7 kN/m 3 m 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the…

A: Given Data Determine a. Second moment of area of cross section. b. Draw the SFD and BMD. c.…

Q: 1. The aluminum rod AB (Ga = 27 GPa) is bonded to the brass rod BD (Gpr = 39 GPa). The portion CD of…

Q: Determine the forces in memeber BD and DE. By method of joints

A: Consider the free body diagram of the given truss as shown below.

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: Given Load PSpan 12 ftTo find out Normal stress in CG

Q: In the structure shown, in diameter pins are used at A, B&D The ultimate shearing stress for the pin…

A: Diameter - ϕpin = 13in Ultimate shearing stress - At point D - σD = 6ksi At AB - σAB = 10 ksi

Q: a) The truss in Figure 2-1 consists of four wooden members, ABC, DEF, BE, and CF, which supports…

A: To find the average normal stress in m

Q: The uniform 2Mg bar is supported by a smooth wall at A and by a pin at B. Determine the diameter of…

Q: In the steel structure shown (see Figure Q1), a 6-mm-diameter pin is used at B and C and

A: According to given data

Q: Problem 2. Two rods connected at B are restrained at points A and C. The section AB is steel and E,…

A: Given,Es=200GPa Alpha s=12.3×10-6/℃ Eb=100GPa Alpha b=21.5×10-6/℃ ∆T=70℃ Dab=50mm Lab=200mm Dbc=70mm…

Q: Exercises: Determine the normal stress in each member of the truss structures. 1. All joints are…

A: Given a=b=2cm

Q: D CED Front view 18 mm 6 mm B B Side view 160 mm 120 mm A Top view In the steel structure shown, a…

Q: Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member…

Q: В b b.

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

Q: The rigid bar EFG is supported by the truss system shown. Determine the cross-sectional area of…

Q: 3) Find a) the maximum stress in the shown member, b) the relative displacement between 8 and D (Ap)…

Q: Compute the shearing stress in the pin at B for the member supported as shown. The pin diameter is…

Q: Use P = 45 kips and cross-sectional area of each member is 5.25 in^2 .

A: Calculation of reaction: Moment at H: Clockwise moment is taken as positive and Anticlockwise moment…

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

Q: The lap joint is connected by four rivets. Assuming that the axial load P = 30000 lb is distributed…

A: Given Shear stress of the rivets= 16 Ksi Bearing stress between rivet and plate = 22 Ksi Tensile…

Q: FOR THE LAP JOINT SHOWN, DETERMINE THE MAXIMUM SAFE LOAD 'P' WHICH MAY BE APPLIED IF THE SHEARING…

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: Determine the moment of intertia about the centroidal x-acid (in mm^4) - Determine the centroid…

Q: 100kN B (EA is constant) A 60KN + Determine the Force in member 4m D BD) se Force method (Consistent…

Q: 2- a)Determine the stresses in members those marked with numbers 1, 2,3, 4. Indicate whether the…

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data Using method of section

Q: Try to write out the stress boundary conditions of the cantilever beam. ( not include the fixed…

A: Three force are there on cantilever beam F force, UVL load and q force.....

Q: Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member…

Q: The supporting bars (1), (2) and (3) shown are made of A992 steel [E = 29,000 ksi] and have equal…

A: Given :

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

Q: 1. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in…

Q: Assume that the clamp shown has been tightened on wooden planks being glued together until P = 420…

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

Q: If the applied load "P" causes the point C to be displaced downward by &c=1 mm, determine the normal…

A: LAC = 210 mmLBC = 480 mm

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Review: Design of simple structures
1.
*1-96. Determine the required cross-sectional area of
member BC and the diameter of the pins at A and B if the
allowable normal stress is allow 3 ksi and the allowable
shear stress is allow = 4 ksi.
1500 lb
-2 ft
-4 ft-
1500 lb
B
60°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pinned joint shown here is held by a 1-cm-diameter pin. The thickness of the two members are t₁ = 0.5 cm and t2 = 1.5 cm. What is the bearing stress when the applied force Fis 150 N? ¹2-F
0.15
0.16
Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. 1500 lb -2 ft -4 ft- 1500 lb B 60°
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
15
Help me urgent
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
13
#2 will upvote anyone who will answer
1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in the figure. Determine the average normal stress developed in each member when the truss is subjected to the load shown. State whether the stress is tensile or compressive. -0.6 in. AAC -3 ft- Auc= 0.8 in.2 AAB 1.5 in. 500 lb B
17