reservoir a has an elevation of 100 m. a piper is connected from reservoir a to reservoir b. it has a length of 950 m. and diameter of 650 mm. a pump is installed near reservoir a and has a rating of 500 hp. if c=100, rate flow is 650 L/s. 1. determine the headloss (meters) in the pipe. a. 6.741 b. 7.428 c. 6.086 d. 7.107 e. none of the above

reservoir a has an elevation of 100 m. a piper is connected from reservoir a to reservoir b. it has a length of 950 m. and diameter of 650 mm. a pump is installed near reservoir a and has a rating of 500 hp. if c=100, rate flow is 650 L/s. 1. determine the headloss (meters) in the pipe. a. 6.741 b. 7.428 c. 6.086 d. 7.107 e. none of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
Draw hp, hes and h, for the system shown in figure (A). Flow V Soil T K=1.5 cm/sec 2 Soil Il K=0.5 cm/sec Figure (A) DIL 1.0 m 1.5 m 1.0 m 1.0 m 1
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
3) A centrifugal pump delivers water between two reservoirs with a 300 ft. elevation difference (Az). The 12-in diameter suction pipe (f1= 0.020) is 100 ft. long (L1) and the 10-in diameter discharge pipe (f2= 0.026) is 5000 ft. long (L2). The pump has a performance curve defined by the equation: h, = 375 - Q² where h, is the pump head in feet and Q is the discharge in ft/s. a) Calculate the discharge, Q. b) Calculate the NPSHA. Assume standard atmospheric conditions, 60°F water, and a pump elevation 8 ft. above the lower reservoir Az D, L2 2 D, Ly. ft LOM
Determine (a) the discharge in the tube immediately after it is opened. Determine (b) the time for the water surface in each tank to be at the same level. Determine (c) the time for the difference in the water surface to be 4 meters.....
A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², Ec=1.9×10¹¹ N/m².
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
None
Question 3) Water transmission line is constructed to transmit water from A reservoir to city with 200 l/s of total discharge. 150 l's is supplied from reservoir and the other part is added from B point (Use same types of pipes through the pipeline). Maximum allowable pressure on the pipeline is 100 m. Minimum pressure of transmission line, (–), = 3 m, William-Hazen coefficient, C is 100. (V = 0.85CR0 Josa ). Determine the diameter of pipeline, design WTL economically. Commercial Pipe Diameters: $200,250, 300,350, 400, 450, 500, 550, 600. 250m 162m (A) (3) 100m 50 V's/ (B) 1000 m 2000 m City 3000 m
46. Situation 16 - The flow of water from Reservoir A shown is 600 L/s. Properties of the system are as follows: a. Determine the water surface elevation, in meters, of reservoir B for the flow to be possible. Round off to two decimal places. b. Determine the flow in Line 3 in L/s. Round off to two decimal places. c. Determine the headloss, in meters, in Line 1. Round off to two decimal places.