Required information Outside an inner, intense-activity circle of radius R, a tropical storm can be simulated by a polar coordinate velocity potential o (r, 0) = Uo R0, where Uo is the wind velocity at radius R. Take surface air density to be sea-level standard, p= 1.225 kg/m3. If, at R = 25 mi, the velocity is 105 mi/h and the pressure is 82000 Pa, calculate the velocity and pressure at r = 100 mi. The velocity is m/s. The pressure is Pa.

Q: Example of how to size a globe valv

A: A globe valve is a type of valve that has a moveable plug or disc element and a stationary ring…

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: how will a vehicle handle if it has too much toe-out?

A:

Q: QUESTION 2 Which of the following is an advantage with the wire ropes in lang lay? OA Do not kink or…

A: given =multiple choice question

Q: what can be caused by excessive negative caster

A: Solution:

Q: QUESTION 4 A wire rope shown below is made with 1/8-inch diameter wires, and it has an outer…

A: given = multiple choice question

Q: what parts provide for toe-out on turns

A: Toe-out on turns is a toe setting for the front wheels so that it can make turns. While making a…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: What additional force A is needed to keep the block in static equi

A: The calculated additional force is needed to keep the block in static equilibrium.

Q: What are the four ways we put fluids to work

A: Crystalloid IV solutions contain small molecules that flow easily across semipermeable membranes.…

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: What precautions should be taken if a hammer is used to shift a part into alignment?

A: Welding is a metal joining process in which two or more parts joined together. Misalignment in the…

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: What type of simple machine is a wheelbarrow? lever inclined plane O wedge screw

A: A machine used to reduce the effort while performing a task is called a simple machine.

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the…

A: Question:- To provide a good sealing joint between the cylinder head and exhaust, apply a sealant to…

Q: When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat…

A: The reconditioning of the valve seats is done to remove cracks, pitting and grooves from its…

Q: The amount of force generated by an air bearing decreases when?

A: The amount of force generated by an air bearing decrease when

Q: Type of Manual control on scrap machine

A: A shaper machine is used for the machining of flat surfaces. It works in the forward stroke and the…

Q: What do varnish or gum deposits on the dipstick indicate?

A: Varnish

Q: Tool marks which are produced by force that are parallel to a surface are known as: Group of answer…

A: Tool marks which are produced by force that are parallel to a surface are known as Striated marks.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.