Required information Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp= 1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T, = 100°C D = 4 cm 2m The air temperature at the 2 m length is Q₁ = 200 W Determine the air temperature at the 2 m length. 57 °C.

Required information Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp= 1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T, = 100°C D = 4 cm 2m The air temperature at the 2 m length is Q₁ = 200 W Determine the air temperature at the 2 m length. 57 °C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I need answer with Details
this cylinder has a rod inside, around the rod there is paraffin wax that will expand, I want to know how to reduce the thickness of this cylinder. However, I don't know what formulas I need to be able to do this and how to do the calculations. Please can you make an example with the data you choose to have an example of how to do this step by step? Thank you Also keep in mind that the wax is expanding by an induction coil, and the heat is happening around the cylinder. And the thickness of the stainless steel cylinder has to be thin but not so thin that it causes a pressure problem.
Choose forming and generating operation 2 points Work Work Thre dsad dsa Generated surface Work Work O dasd dsaa
Hello ! I hope you are well.Why are we taking this specific cross section for the second part of the question ? Is it because it's the one where the nails are ?
Explain with neat sketch, the surface finishing process of “Sandblasting
Compare and contrast the differences between Paul Richer’s and Andrew Loomis’ concepts of proportions when drawing human characters. Explain your answer with some examples.
Properties of areas of common shapes. INCLUDE ALL THE REFERENCE (LINKS)
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
Give the definition of the following drawing materials and state their functions.
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
1. Define manufacturing processes, design engineer, industrial engineer and materials engineer? 2. Name and explain a protess to make cylinder shaft? 3. Discus at least three factors which will effect tool life? 4. Define finishing and roughing process? 5. Explain the negative effect of heat generated from machining process? 6. One limitation of sand casting is bad surface finish. Yes or No? Why? 7. What is permeability in casting process? 8. What are the major defects in casting process? 9. Which type of casting process should be use for high melting point casting, such as cast iron and why? 10. Casting problem A certain mold has a sprue whose length is 20 cm and the cross-sectional area at the base of the sprue is 2.5 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm³. Determine: (a) velocity of the molten metal at the base of the sprue, (b) volume rate of flow, and (c) time to fill the mold (in second). mfg m1 Spring 2020 999.pptx
In one sentence, explain the difference between straightness and flatness.