Required information A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion BC is made of steel (Es= 29 x 106 psi and a, = 6.5 × 10-6PF) and portion AB is made of aluminum (E, = 10.4 x 106 psi and a, = 13.3 x 106PF). The rod is initially unstressed before a temperature rise of 72°F. 24 in.---32 in. 24-in. chameter 1-in. diameter Determine the normal stress induced in portions AB and BC due to the temperature rise.

Required information A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion BC is made of steel (Es= 29 x 106 psi and a, = 6.5 × 10-6PF) and portion AB is made of aluminum (E, = 10.4 x 106 psi and a, = 13.3 x 106PF). The rod is initially unstressed before a temperature rise of 72°F. 24 in.---32 in. 24-in. chameter 1-in. diameter Determine the normal stress induced in portions AB and BC due to the temperature rise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer clearly with free body diagram don't waste my question I will vote it up for your effort thanks.
If p is 160 Lb,what is the member BD (FBD) (assuming tension), and what are the components of C?
Problem 1A steel wire is 6 m long, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa.
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
- once answered correctly will UPVOTE!!
2
Ineed answer within 20 minutes please please with my best wishes
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
Consider a deformable homogenous slender rod of constant area along its length. It is axially loaded at points A and C. According to Saint-Venant's Principle, which of the following point(s) is/are the actual maximum axial stress underestimated the most by the average stress? A B. F F L
Problem (01): The pin-jointed truss in Figure (6) supports a load of P-2 kips at joint C. Determine the axial forces F, through Fs in the truss members. (1) (3) (2) 6ft (4) (5) 8 ft Fu9-
I need the answer as soon as possible
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648