Represent the electrical network shown in the following in state space, where vi(t) is the input and v0(t) is the output. 12 V2 Vo + 1H 1F V.(t) v;(t) 1H 0000

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: The elevation and tilt angle of table AB are controlled by an operator's hand at point D. The table…

A: Freebody diagram of Table AB:Freebody diagram of the member DCB:

Q: For problems 1 and 2 below, using the Parallelogram method only (no other method will be accepted)…

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: F 400 N E-600 N 45 30

A: Given: F1 = 600 N F2 = 400 N   To find: FR = ? and direction of resultant using parallelogram law of…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: 1. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram…

A: As meter stick is balanced when fulcrum is at 49.7 cm, this distance is the center of gravity (G) of…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.