Answered: Regulators are used in control system,…

Engineering

Electrical Engineering

Regulators are used in control system, if output changes beyond the set limit of tolerances. Select one: O True

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter11: Float Switches

Section: Chapter Questions

Problem 7SQ

See similar textbooks

Related questions

Q: 3. For the indicated combination of springs, masses and dashpots, draw both the mobility analog and…

A: The quality analogy conjointly called the admittance analogy or the Firestone analogy could be a…

Q: Vending machine. After joining a circuit design company, you are asked to design the control circuit…

A: We need to design the control circuit of a vending machine that sells a type of bottled soft drink.…

Q: Are electronic devices that take in analog signals and interpret them into digital data. (A) All of…

Q: 1. In English: How does one show that a system that multiplies two signals must be a nonlinear one?…

A: According to the question, How does one show that a system that multiplies two signals must be a…

Q: Could you please show the solution step by step without skip any steps for this kind of…

A: For the two subparts of Question 1c given, input x[n] and output y[n] are shown, and they are…

Q: Reference 7 segment display: Solve for the segments: "d, e, and f." Show your work 1. KMAPs 2.…

A: To solve for segments d, e, and f in a 7-segment display, we can follow these steps:Karnaugh Maps…

Q: A 500v, 50kva. 1-p altemator has an effective resistance of 0.2w. A field current of 10a produces an…

A: Voltage regulation: It is the ratio of the full load voltage to the no-load voltage. This should be…

Q: The block diagram reduction process takes more time for complicated systems. Because we have to draw…

A: Its true that block diagram reduction technique takes more time due to draw blocks at every step.

Q: Which of the following has a sine look-up table stored in memory? ODDS chip OPLL chip O Op amp O All…

A: The sine look-up table is used by the synthesizer to generate the sinusoidal waveform and it will be…

Q: Complete the following decimal-to-hexadecimal number conversions. If available, use the base…

A: 1) Decimal to hexadecimal While convert from decimal to any destination base, we divide the decimal…

Q: Get the same shape required and Give proper label and title by using OCTAVE and write the program

A: Get the same shape required and Give proper label and title by using OCTAVE and write the program

Question

Solve it quickly please

Regulators are used in control system, if output changes beyond the set limit of tolerances.
Select one:
O True
O False

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Voltage Regulator and Power Supply 3
Q31Answer the following questions 1.Explain briefly the diode and forward bias and reverse bias of it with drawing? 2.Explain briefly with draw the mechanism of Relay?
Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
Answer the Question Briefly..!!
i need ans in 15 min
Problem: Assume a regulator has a percent load regulation of 0.5%. What is the output voltage at fullload if the unloaded output is 12.0 V? Express the numerical value up to 2 decimal places.
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
a) Figure 3 illustrates a thyristor phase control circuit and associated waveforms. Describe the function of the control element in the circuit towards the output at the load. Identify the best-suited application to describe the control circuit. Lamp Load VAC SCR r 9 8₁ Conduction MM h 18₂ h Gate Trigger Pulse
Please answer this question asap
exercise 2
- In d.c. generators armature reaction is produced by armature current O none of the mentioned compensating winding current field current O commutating winding current The use of d.c. generators elminated the use of rectifiers and ac supplies True False s If the number of layerallot is 4 then the number of colls the number of slots Equal to O none of the mentioned O twice O half O s In 2-pole machines: the wave winding have greater generated voltage than the lap winding'armatures True False For high rotating speed machines the number of poles munt be Little Tiue O Fale O O O
What effect does the switching frequency have on the power loss due to the collector current during the conduction period A. A Higher switching frequency increases power loss B. A Higher switching frequency decreases power loss C. Power loss is directly proportional to the switching frequency D. Switching frequency has no effect on the power loss