Refer to the figure showna = 11,7 x 10°/°cE = 200 GPaA = 1,200 mm²a = 23 x 10/°CE = 70 GPaA = 900 mm2%3D%3D%3D%3D%3D%3D200 kN+A300 mm200 mm-Determine the displacement of jolnt B.Select the correct response:0.1794 mm0.1974 mm0.4179 mm0.1497 mm

Answered: Image /qna-images/answer/0c6a9bcc-9cfa-4c6a-8519-7d97d3add634.jpg

Refer to the figure shown a = 11.7 x 10/°c E = 200 GPa A = 1,200 mm2 a = 23 x 10/°C E = 70 GPa A = 900 mm? %3D %3D %3D %3D %3D %3D 200 kN+ 300 mm 200 mm- Determine the displacement of joint B. Select the correct response: 0.1794 mm 0.1974 mm 0.4179 mm 0.1497 mm B.

Refer to the figure shown a = 11.7 x 10/°c E = 200 GPa A = 1,200 mm2 a = 23 x 10/°C E = 70 GPa A = 900 mm? %3D %3D %3D %3D %3D %3D 200 kN+ 300 mm 200 mm- Determine the displacement of joint B. Select the correct response: 0.1794 mm 0.1974 mm 0.4179 mm 0.1497 mm B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the truss shown below, determine the vertical displacement at point F. Cross- sectional area of bars = 15,200 mm². Modulus of Elasticity of bars = 210 GPa G 35 kN 15 kN H F 8 m A E C D 3 m 3 m 3 m 3 m B.
3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa A 3.5 m FIGURE 3 P B Steel L= 4m A = 300 mm² E = 200 GPa 2.5 m C
A column is constructed using four A992 steel angles that are laced together as shown. The length of the column is to be 40 ft and the ends are assumed to be fixed connected. Each angle shown below has an area of A = 2.75 in^2 and moments of inertia of Ix = ly = 2.22 in^4. (Figure 1) 2.068 in. 0.932 in. 0.932 in. 2.068 in. C с C C y Determine the distance d between the centroids C of the angles so that the column can support an axial load of P = 340kip without buckling. Neglect the effect of the lacing. Express your answer to three significant figures and include the appropriate units X d
Can you show how 184 appear? This is the problem: The beam shown in figure is 5 inches wide and 10 inches deep. What is the maximum bending stress?
If the unit mass of steel is 7850 kg/m3 and E = 200 x 103 MN/m2, find the total elongation of the rod given a steel rod having a cross-sectional area of 200 mm2 and a length of 120 m is suspended vertically from one end. It supports a tensile load of 18 kN at the lower end. O a. 56.77 mm O b. 59.68 mm O. 52.45 mm O d. 53.44 mm
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
number of significant digits; the tolerance is +_1 in the third significant digit
Identify the Degree of Hyperestaticity and define the Main System, indicating the State of Displacement and the State of Virtual Load.
There is a wooden beam AD, as shown in the figure below, the Flexural Rigidity of the beam section is constant EI:(a) Try to find the slope of point A and point C after deformation.(b) Try to find the (vertical) displacement of point D after deformation.(c) What is the position and magnitude of the maximum displacement after deformation?
The steel beam shown in the figure 2 is made by a steel type that has σY=250 MPa and σU=400MPa Determine the maxium torque that can be applied to the beam when it is bent aroung the x axis.
The subject is Statics of Rigid Bodies
SITC. Determine the horizontal displacement (mm) of joint C. 300 lb 300 lb 13 ft B 5 ft 12 ft 13 ft 12 ft