Refer to the figure below. The square steel tube carries 130 kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 2000 N. 100 mm 100 mm 4 mm Standard strudural steel tube-100x 100x 4 ,150 mmx 150 mm plate 300 mmx 300 mm Concrete pier 600 mm 600 mm Gravel

Refer to the figure below. The square steel tube carries 130 kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 2000 N. 100 mm 100 mm 4 mm Standard strudural steel tube-100x 100x 4 ,150 mmx 150 mm plate 300 mmx 300 mm Concrete pier 600 mm 600 mm Gravel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steel bar 0.75 in. in diameter has an axial load P = 13,000 Ibs. 0.75 in. P 30° -

A: Load on bar, P =13000lbDiameter of cross section, D=0.75inAngle of linclined plane with vertical…

Q: A vinyl [E = 2.80 GPa; v = 0.41] block with width b = 50 mm, depth d = 100 mm, and height h = 270 mm…

A: E = 2.8 GPa = 2.8 × 103 N/mm2Poisson's ratio (μ) = 0.41Determine the change in the depth dimension…

Q: hollow cast iron column with the cross section shown in the image attached is subjected ti a…

A: A vertical point load acting at A of magnitude 100kNTo determine the maximum compressive and tensile…

Q: 3 Given a concrete beam (width b= 10 in., depth h=25 in.) with flexural reinforcement at the bottom,…

A: Cracking: When the stresses or the forces which are imposed on the structure cannot be resisted by…

Q: The following geomotry and basic clata for a concrete The dam s are given In reservoir figure below.…

A: Consider unit length of the dam.

Q: 1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly…

A: To determine,A. Determine the normal stress in the steel. B. Determine the normal stress in the…

Q: estion 11 A pipe steel column is under ax: Assuming a modulus of elasticit a. Find the compressive…

A: Given data: Axial load acting on the column, P = 228 kN Length of column = L = 3.05 m Outside…

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

Q: Draw the V&M diagrams and calculate the largest permissible value of P for the beam and loading…

A: Allowable normal stress in tension=-80MPa Allowable normal stress in Compression=-140MPa To find…

Q: The properties of the reinforced concrete beam are b = 310 mm, d = 467 mm, Ast = 1173 mm2, and Est /…

A: Bending Moment is 57.20 x 103 Nm or 57.2 KN-M.

Q: A composite beam is constructed using a steel plate (14 mm x 125 mm) with two wood beams (75 mm x…

Q: determine the minimum force P required to punch the slot. Punch O 575 kN O 675 kN O 724 KN Slug…

Q: 11.18 A long, flat steel bar 4 in. wide and 3 in. thick is reduced in width to 3 in. There are…

A: Applied load (P)=12000lb D=4in d=3 in Thickness (t)=3/8 in

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Refer to the figure below. The square steel
tube carries 130 kN of axial compressive
force. Compute the compressive stress in the
tube and the bearing stress between each
contacting surface. Consider the weight of
the concrete pier to be 2000 N.
100 mm
100 mm
4 mm
Standard strutural steel tube-100x 100x 4
150 mmx 150 mm plate
300 mm x 300 mm
Concrete pier
600 mm
600 mm
Gravel

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel loop ABCD is placed around a 1.0 in. diameter aluminum rod AC. Cables BE and DF, each of 0.5 in. diameter, are used to apply the load Q. What is the largest allowable Q if the axial stress in cable BE stays under 23 ksi while the max axial stress in the aluminum rod AC is under 13 ksi? Reference: Beer, et.al., 7th Edition Mechanics of Materials 9 in. Į 9 in. ↓ A 12 in. 1 in. 4 E * F B D Q' 12 in. in. in. C
The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E= 25 GPa for concrete 900 KN 250 mm 375 mm stress in steel = 65.3 MPa and stress in concrete = 6.4 MPa stress in steel = 67.3 MPa and stress in concrete = 8.4 MPa stress in steel = 69.3 MPa and stress in concrete = 10.4 MPa stress in steel = 71.3 MPa and stress in concrete = 12.4 MPa O
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
what is the loading in pounds that you need to achieve vertical stress of 15 psi? Assume all the loading will put on the one-to-one ratio hanger. Assume a diameter of 2.5in.
A prestressed concrete beam of rectangular section 300mm wide and 600mm deep is prestressed by 5 pieces of 8mm high tensile wires at 500mm from the top and 15 pieces of 8mm diameter high tensile wires at 83 mm from the bottom. The initial stress in the wires is 1200 MPa. Estimate the loss of stress in the bottom wires due to elastic shortening of concrete. Assume modular ratio = 6.
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks