Recall that muscle generates force at 30 N/cm?. Two cross sections are taken from the rectus femoris muscle (bipennate muscle similar to the diagram below). The length and width of the first cross section is 6 cm and 5 cm respectively with a 35° angle of pennation. The length and width of the second cross section is 5.6 cm and 3 cm respectively with a 31° angle of pennation. What is the predicted maximum tendon force (FTendon) of this muscle in Newtons? Answer to the nearest 0.1 N. Freadas

Recall that muscle generates force at 30 N/cm?. Two cross sections are taken from the rectus femoris muscle (bipennate muscle similar to the diagram below). The length and width of the first cross section is 6 cm and 5 cm respectively with a 35° angle of pennation. The length and width of the second cross section is 5.6 cm and 3 cm respectively with a 31° angle of pennation. What is the predicted maximum tendon force (FTendon) of this muscle in Newtons? Answer to the nearest 0.1 N. Freadas

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the normal strain developed in wire CD: ___ mm/mm. Calculate your answer to 4 digit place.
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Calculate modulus of resilience.
Q2
DIRECTION: Identify the following term. 2. It is used to determine the internal resultant loadings acting on the surface of a sectioned body. In general, these resultants consist of a normal force, shear force, torsional moment, and bending moment.
Problem 2 refers to the following: a load P is applied to the cantilever beam shown which causes it to bend and deflect elastically: 2. a. b. 6 C. Gage 1 2 3 4 5 6 5 3 4 on bottom Strain (ue) A student group recorded the following strains from the loaded beam but failed to record which gages (1-6) the strain recordings came from (all strains are in microstrain): -154, 318, -23, 555,-323, 81. 2 1 Write the correct strain readings in the table above. Note gages 1, 3, 4, and 5 are longitudinal gages, and gages 2 and 6 are transverse gages. Gage 4 is on the bottom of the beam and is the same distance from the load as gage 3. Calculate an estimate of Poisson's ratio for this material. If the elastic modulus for this material is 10 Mpsi, calculate the uniaxial stress at the location of gages 5 & 6.
None
Draw shear force and bending moment diagrams. 10 lb 816 3º 12 lb (A) | 15 N 余文大早林木 3m 2m 10N/m (B)
Required information Stairs leading to a balcony are shown below. |400 lb dimensions in inches 40° 144 600 lb 32 22 16 38 30 30 For the 400 lb and 600 lb forces, and if F= 155 lb and P= 0, determine the reaction at point Dand the force supported by bar BE. The reaction at point Dand the force supported by bar BE are as follows: Dy= 410 Ib TBE = - 701.798 Ib
only HANDWRITTEN answer needed ( NOT TYPED)
I want handwriteen and correct answer only don't do if u don't knowpls
1 Required information Consider given force vectors. Take F= 15 lb. y Q = 60 lb 30° 20 60° 60° 45° P = 100 lb Write an expression for each force using Cartesian representation, and evaluate the resultant force vector. = (- 4.58 i + 26.83 12.6 k ) lb 39.8 i + 30 j 33.4 k) lb 70.7 50 k) lb 50 85.22 i 13.87 29.2 k) Ib %3D
Could you please provide correct answer as fast as.