Read the questions carefully and answer with complete solution and units. Use the steam tables provided and use 4 decimal places for solving. Final answers shown are in 2 decimal places. Draw the T-S diagrams properly with respect to the saturation line 1.) A steam power plant uses the ideal Reheat Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then it is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate 3241.70,2144.67, 1101.06 , 4.03, 1097.03,33.84%, 3.28- kg kg kg kg kg kg kWh

Read the questions carefully and answer with complete solution and units. Use the steam tables provided and use 4 decimal places for solving. Final answers shown are in 2 decimal places. Draw the T-S diagrams properly with respect to the saturation line 1.) A steam power plant uses the ideal Reheat Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then it is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate 3241.70,2144.67, 1101.06 , 4.03, 1097.03,33.84%, 3.28- kg kg kg kg kg kg kWh

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 2. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
Read the questions carefully and answer with complete solutions and units. Use the steam tables provided and use 4 decimal places for solving. Draw the T-S diagrams properly with respect to the saturation line. A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The maximum pressure of the cycle is 15 MPa, and the minimum pressure is 5 kPa. Steam initially enters the turbine at 500C. a.) Draw the proper T-S diagram of the cycle with a proper label for the points. b.)Find the quality of the steam entering the condenser, Qa, Qr, Wt, Wp,Wnet, efficiency,mass flow rate and steam rate
Question 4 a. A factory requires electrical power for its machinery along with 80 MW of heat for process heating. The combined demand is achieved by using a superheated Rankine steam cycle in which the turbine is used to supply the electrical power required and the condenser cooling water provides the process heating to the factory. Steam is generated in a boiler at a pressure of 70 bar and it leaves the superheater at a temperature of 400°C. The steam expands through the turbine to a condenser pressure of 3 bar. The turbine isentropic efficiency is 0.85. The steam is condensed to saturated liquid in the condenser and a feed pump increases the condensate pressure to 70 bar for return to the boiler. The feed pump work may be neglected in the calculation. i. Sketch the cycle in a T-s diagram. ii. Calculate the steam mass flow rate required to satisfy the process heating demand. iii. Calculate the power available from the turbine. iv. Determine the thermal efficiency of the cycle.
A reheat cycle with two stages of reheating is executed with steam expanding initially from 200 bar (20 Mpaa) and 540 deg C. The 2 reheater pressures are 40 bar (4 Mpaa) and 10 bar (1 Mpaa) and the steam leaves each reheater at 540 deg C. Steam is bled in between two reheating sessions at a pressure equal to 20 and 15 bars into 2 open feedwater heaters. Condensation occurs at 60 deg C. All expansion and compression efficiencies are 90 %. There is a total of 10.3 kg/sec of steam (total mass flow rate m) circulated in the cycle. Answer the following: fill up the blanks in the items below: Equipment layout and TS diagram for the cycle. Ideal turbine work (KW) Ans:_______________________________ Actual mass of steam bled into the open heater m1’= _____________kg/sec for the heater nearest to the SGU/boiler and m2’ = _____________________kg/sec for the heater nearest to the condenser. Actual engine efficiency (%) Answer: _______________________ Actual Rankine cycle efficiency %…
Answer letters A, H, I. Use the steam tables provided and DO NOT ROUND the values from the steam table. Write down the values taken from the steam table
My Question: In the steam plant problem#2, the reheater developed a leak and it was decided to run the plant bypassing the reheater. Determine the thermal efficiency and steam flow rate to develop the same power output.Problem 2 (In a reheat cycle steam enters the high-pressure turbine at 40 bar and 400C. It expands isentropically to 6 bar and is reheated at constant pressure to 400C. This steam is expanded isentropically in the low pressure turbine to the condenser pressure of 0.1 bar. Calculate the thermal efficiency and steam consumption for 10 MW output.)
A reheat cycle with two stages of reheating is executed with steam expanding initially from 200 bar (20 Mpaa) and 540 deg C. The 2 reheater pressures are 40 bar (4 Mpaa) and 10 bar (1 Mpaa) and the steam leaves each reheater at 540 deg C. Steam is bled in between two reheating sessions at a pressure equal to 20 and 15 bars into 2 open feedwater heaters. Condensation occurs at 60 deg C. All expansion and compression efficiencies are 90 %. There is a total of 10.3 kg/sec of steam (total mass flow rate m) circulated in the cycle. Answer the following: fill up the blanks in the items below: Actual Rankine cycle efficiency % using Qa’ and Qr’ values Answer: _____________ If the generator efficiency = 95%, brake engine efficiency = 90% what is the plant capacity in MW? Answer: ______________________ If Cp water = 4.187 KJ/kg-K; cooling water enters the condenser at 12 deg C and leaves at 21 deg C, find amount of cooling water needed by the condenser in kg/sec. (ACTUAL) Answer:…
Please solve the question on the sheet and get a clear picture and submit the picture. thankyou
Completely solve and box the final answers. Write legibly
Read the questions carefully and answer with complete solution and units. Use the steam tables provided and use 4 decimal places for solving. Final answers shown are in 2 decimal places. Draw the T-S diagrams properly with respect to the saturation line A steam power plant uses the ideal Regenerative Rankine cycle with single open feedwater heater where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then some steam is extracted at this point. The remaining steam expands and enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kg 20.01%, 2286.401457.51,832.543.74,828.89, 36.25%, 4.34 kWh 1
Complete solution and units please. Use the steam tables provided, and use 4 decimal places for solving. Final answers are shown in 2 decimal places. Draw the T-S diagram properly with respect to the saturation line. 2. A steam power plant uses the ideal Regenarative Rankine cycle with single open feedwater heater where the steam enters the high pressure turbine at 4 UPa and sooc. At partially expands to 600 kPa then some steam is extracted at this point. The remaining steam expands and enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for marr taken for feedwater heating, Qa, Qr, Wt, Wp. What, thermal exter efficiency and Steam rate. Neglect the condensate pump work." Answer: 20.01% 2286.40 kJ. 1457.51 kJ 1 832.54 kJ 1 kg 3.74 kJ kg kg 36.25%, 4.34 £] 828.89 kJ " kg ку. kuh Specific Volume Internal Sal. Enthalpy Press. MPa Se Entropy Sat, V Sat. Sat. Sat. Evap. Liquid Evap. Vapor Vapor р 10¹ Liquid Uy 103 apor U₂ h, hre h₂…