For all the computations and the final answer, please set it to four (4) decimal places for consistency. QUESTION 1. Consider a 65 MW steam power plant operating on a regenerative Rankine cycle with one open feedwater heater operating at 1 MPa. Steam enters the turbine at 16 MPa and 560°C, with a condenser pressure of 8 kPa. Determine mass flow rate of the steam (kg/h), the thermal efficiency (%) of the cycle and the mass of the cooling water (kg/ h), if the temperature rise in the cooling water is 10 °C.

For all the computations and the final answer, please set it to four (4) decimal places for consistency. QUESTION 1. Consider a 65 MW steam power plant operating on a regenerative Rankine cycle with one open feedwater heater operating at 1 MPa. Steam enters the turbine at 16 MPa and 560°C, with a condenser pressure of 8 kPa. Determine mass flow rate of the steam (kg/h), the thermal efficiency (%) of the cycle and the mass of the cooling water (kg/ h), if the temperature rise in the cooling water is 10 °C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please use property tables. Thank you Steam enters the high-pressure turbine of an ideal reheat Rankine cycle at 10 MPa and 500°C. The low-pressure turbine inlet admits steam at 1 Mpa. Assume that the pump inlet is a saturated liquid at 10 kPa and that 80 MW of power is produced overall. 1. Report the amount of heat added in the reheat process, in kJ/kg, to one decimal place using rounding. 2. Report the amount of work produced in the low-pressure turbine, in kJ/kg, to one decimal place using rounding.
Problem 2 Consider a reheat Rankine cycle utilizing steam. Steam leaves the boiler and enters the turbine at 600 psia, 800 °F. After expansion in the turbine to 60 psia, the steam is reheated to 800 °F and then expanded in the low-pressure turbine to 1 psia. After presenting a schematic of the problem in addition to clearly labeled and explained T-s and h-s diagrams, you are asked to determine the following: (a) Pump work required per Ibm of working fluid. Quality of fluid at turbine inlet. (b) (d) (e) (f) Work output of turbine per Ibm of working fluid. Energy input to the boiler per Ibm of working fluid. Heat rejection by the condenser per Ibm of working fluid. Determine the cycle thermal efficiency.
A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 15 MPa and 10 kPa. The mass flow rate of steam through the cycle is 12 kg/s. Steam enters both stages of the turbine at 500°C. The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 5 percent. Determine a) the total rate of heat input in the boiler and b) the thermal efficiency of the cycle
Draw a schematic diagram of this problem.
High-P turbine Low-P turbine Reheater (4) Boiler P4 = P5 = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the temperature in degree C at state 4 to 2 deciamal places.
Rankine Cycle (Thermodynamics) Show the illustration diagram and complete and step by step solution.
A steam power plant operates on an ideal regenerative Rankine cycle. Steam enters the turbine at 5 MPa, 450 ∘C, and is condensed in the condenser at 15 kPa. Steam is extracted from the turbine at a pressure of 0.4 MPa and enters the open feedwater heater. Water leaves the feedwater heater as a saturated liquid. A) Determine the thermal efficiency of the cycle. B) Determine the net work output per kilogram of steam flowing through the boiler. (W_net)
A Rankine cycle with a thermal efficiency of 42% produces 100 kW of net power. What is the rate of heat transfer into the boiler? Round your answer to the nearest whole number.
Required information Problem 10.019 - Power plant operating in simple Rankine cycle - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500°C and is cooled in the condenser at a pressure of 15 kPa. Problem 10.019.b - Quality of steam at turbine exit Determine the quality of the steam at the turbine exit. Use steam tables. (You must provide an answer before moving on the next part.) The quality of the steam at the turbine exit is
Boiler High-P turbine LOW-P turbine Reheater 4 P₁ = P5 = Preheat P4 2 Pump Condenser 1 The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg Find the specific entropy in kJ/kg at state 1 to 3 decimal places.
1. The ideal Rankine cycle is shown below in schematic form and on a T-s diagram. The turbine power output of this cycle is 2 MW. Saturated liquid at 20 kPa leaves the condenser, and the vapor at the turbine exhaust has a quality of 95 percent. The boiler pressure is 1.4 MPa. Determine the mass flow rate of steam, the heat-transfer rate in the boiler, and the thermal efficiency of the cycle. Pump Boiler 2 pie Condenser P= constant P= constant 3 3 Turbine
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 72 percent and that of the pump is 95 percent. Determine the quality (or temperature, if superheated) of the steam at the turbine exit. Use steam tables. (You must provide an answer before moving on to the next part.) The temperature of the steam at the turbine exit is °C.