Required informationProblem 10.019 - Power plant operating in simple Rankine cycle - DEPENDENT MULTI-PART PROBLEM -ASSIGN ALL PARTSNOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPaand 500°C and is cooled in the condenser at a pressure of 15 kPa.Problem 10.019.d - Mass flow rate of the steamDetermine the mass flow rate of the steam.The mass flow rate of steam iskg/s.

Here, given that work output of plant, Power=210 MW For Turbine's inlet state P1=10MPa and…

Answered: Determine the mass flow rate of the…

Engineering

Mechanical Engineering

Determine the mass flow rate of the steam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem 3. Consider a shower that mixes hot and cold saturated liquid water to maintain a steady…

Q: 14 Required information rt 2 of 3 NOTE: This is a multi-part question. Once an answer is submitted,…

Q: Identify the state of the fluid: Ammonia at 120kPa, with a specific enthalpy of 35 kJ/k

Q: Differentiate between a saturated vapour and a superheated vapour?

A: Vapour: A phase of a fluid at a temperature where the same substance can exist in both solid and…

Q: a. What is shown in the figure? Where is it used and how does it work? b. What is the nature of heat…

A: a. Heat exchangers are devices that allow heat to be transferred from one medium to another.…

Q: A single-effect evaporator concentrates 4.00 kg/s of a 10% by mass solution of H2SO4. The entering…

A: Given that, Mass flow rate of solution, F=4 kg/sec,xF=0.10Mass flow rate of vapor, V=3.2 kg/second,…

Q: A boiler takes in water at 200 degrees Celsius and 13 MPa (1) and another water at 1.0 MPa (2), and…

A: At 13 MPa: Saturation temperature→Tsat1=331°C And →hf=1532.43 KJKg and hg=2726.66 KJKg But initial…

Q: A juice at a rate of 500 kg/h is heated from 60 °C to 115 °C. The juice has a specific heat of 3.85…

A: Introduction In this problem, we will calculate the mass flow rate of steam with the help of the…

Q: Final Exam Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm…

Q: What is the work done by the turbine if the mass flow is unknown?

A: From previous solution,Wpump=4.03097 kJ/kgh1=3674.9 kJ/kgh2=2959.3629 kJ/kgh3=3273.9…

Q: Drow and explainthe use of vr data for calculating the final temperature during an isentropic…

A: The use of Vr data for calculating the final temperature during an isentropic process can be easily…

Q: An automobile cylinder has a minimum volume (top dead center) of 50 cm3. Its maximum volume (bottom…

Q: The compressor tank that holds 80L of air during compression of pressure of 250kpa and the…

A: The gas which follows PV=mRT equation is known as Ideal Gas Equation. There are two conditions which…

Q: Determine the total turbine power output ? in the adiabatic turbine receives the water at (15000…

A: Given Data

Q: The air has a dry ball temperature of 40 ℃ and a wet bulb temperature of 26 ℃ initially heated in…

A: On the basis of given information we can draw the process as shown. process 1 to 2 is sensible…

Q: So the initial pressure is 0.8Mpa?

A: Initial condition of refrigerant R134a, V1=0.05 m3, T1=32oCFinal pressure of R134a, P2=0.4 MPa

Q: air at 30 ℃ and RH 40% flowed to the heating coil so that the dry bulb temperature was 80 ℃. then…

A: Given State 1: DBT 30 deg C and RH 40% State2 by heating: DBT 80 deg C State 3 by passing into pet…

Q: A steady flow of steam enters a turbine with a specific enthalpy of 2200 kJ/kg and at negligible…

A: Given:h1=2200 KJ/Kgh2=1900 KJ/Kgm=2 Kg/s

Q: What is the heat transfer rate required to condense the water, cool the water vapor, and cool the…

A: An air-conditioner cools a flow of ambient moist air at 30°C and 80% relative humidity with 0.24…

Q: Determine the expression for the final temperature of the mixture in terms of the rate of heat…

A: Equating energies at inlet and exit

Q: Distinguish between ideal and real pumping processes n an enthalpy-entropy (h-s) diagram.

A: Pumping process consumes power when undergoes the steady flow process. The isentropic efficiency of…

Q: Steam at an initial enthalpy of 100 kJ/kg and inlet veloc- ity of 100 m/s, enters an insulated…

A: Given data: h1=100 kJ/kgV1=100 m/sV2=200 m/s Need to determine the exit enthalpy of steam.

Q: Refrigerant R-134a enters to the compressor of a refrigeration machine at a pressure of 140 kPa and…

A: In this refrigeration cycle, there are four processes Process 1-2 Isentropic compression Process 2-4…

Q: As the airr is heated along the constant WBT line the enthalpy of air

A: Heating of Air at constant WBT line. Required: Effect of heating at constant WBT line on the…

Q: The turbine's inlet is connected to a steam throttling valve with inlet conditions of 3MPa and 500C,…

Q: A steady flow of steam enters a turbine with a specific enthalpy of 2200 kJ/kg and at negligible…

Q: request to I don't canc

Q: Q2 5-26. An adiabatic diffuser in a jet engine is designed to decrease the kinetic energy of the air…

Q: Volume of the tank capacity of 1500 kg is used for the cooling process. The product temperature in…

A: Givenm=1500kgT1=85oCT2=45oCQ=15m3/hr

Q: At a flow rate of .5000 m3 / h, saturated air at a temperature of 2 ° C is heated sensibly up to a…

A: flow rate , Q=5000 m3/hr or 1.389 m3/secdensity of saturated air, ρ=0.00485…

Q: Steam enters a nozzle at 350C and 800 kPa with a velocity of 12 m/s, and leaves at 250C and 200 kPa…

Q: In Otto Cycle, air at 18oC is first compressed to one- eight of its original volume. If the heat…

Q: A tubing is used to feed water to a bioreactor. Water enters the tubing at a mass flow rate of 5…

A: The compressibility chart can be used to determine the compressibility factor for the given reduced…

Q: rat 40°C dbt and 55% RH is passed over a t exit from coil the air is saturated and itst leaves at…

A: given:

Q: 5 kg/sec of steam enters the condenser at 0.10 mpa and 88% quality. The cooling water enters @ 33C…

A: Given, Steam: P1=0.1 MPa x1=0.88 ms˙=5 kg/s Cooling water: Tin=330CTout=390C Note: 1 m3=1000 L1…

Q: What do you mean by intermediate-pressure steam? Is the pressure of the inlet the same as that of…

Q: A gas flows steadily through a rotary compressor at a temperature of 16 ⁰C, a pressure of 100 kPa,…

A: (a) The external work done per unit mass of gas can be calculated as follows: External work done per…

Q: ressure. Show the

A: given: Explain the process of steam generation at constant pressure. Show the various stages on p-v,…

Q: Determine the enthalpy of steam at 127C, at 75% quality, and flowing at the rate of 70 kg/h, if it…

A: Answer: (a) The enthalpy of steam at 127℃ and 75% quality is 2170.3235 kJ/kg. (b) The volume of…

Q: The change of enthalpy of air in the cooling tower is 82 kJ/ kg and the mass flow of air is 215 kg/…

A: The change of enthalpy of air in the cooling tower ∆hair =82 kJ/ kg Mass flow of air ma= 215 kg/min…

Q: and (d) heavy fuel oil at 25°C

A: Given Flow rate, Q = 6.6667 x 10-5 m3/s For, heavy fuel oil at 25°C Kinematic…

Q: Air is drawn into the compressor at pressure of 100 kPa and temperature of 22ºC. The volumetric flow…

A: Disclaimer from Bartleby:Hello. Since your question has multiple sub-parts, we will solve the first…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Required information
Problem 10.019 - Power plant operating in simple Rankine cycle - DEPENDENT MULTI-PART PROBLEM -
ASSIGN ALL PARTS
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa
and 500°C and is cooled in the condenser at a pressure of 15 kPa.
Problem 10.019.d - Mass flow rate of the steam
Determine the mass flow rate of the steam.
The mass flow rate of steam is
kg/s.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steam power plant of 40% thermal efficiency receives heat of 150 MJ at high temperature while burning fuel. The amount of work required to circulate the water in the plant is 10 MJ. Determine the amount of the rejected heat to the surrounding and the amount of work delivered by the steam as it expands in the .turbine
You are designing a system to mix fuel and air prior to ignition in an engine. Do you want the flow to be laminar or turbulent? Why?
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet. Find the ideal gas using the equation.
Air expanded from 0.05m3 to 0.3m3 with a temperature change of 20K at a constant pressure of 3atm. What is the heat added and work done by the gas?
DESCRIBE THE INTERNAL ENERGY, ENTHALPY, AND SPECIFIC HEATS OF SOLIDS AND LIQUIDS
An entrance point that is located six meters above the ground is used by an isentropic air pump that has a distance of only 0.3 meters between its inlet and its outlet. It was positioned in a vertical orientation, drawing in air from the surrounding atmosphere, and pumping air directly downward into a storage tank. The pressure relief valve on the tank has a rating of 300 kPa when it comes to its operating pressure. The outlet diameter for the tank is to be set at 200 millimeters, and the filling rate is to be 0.7 cubic meters per minute. The air is compressed to 38 degrees Celsius despite having a temperature of only 29 degrees Celsius before it was compressed. What is the volume of the air that is being taken in by the system and the amount of heat that is being rejected by it if the amount of work that has been done is 70 kW?
Q) Water flowing through a tube of 1.5 cm diameter is heated from 70°F to 88°F while the tube surface is maintained at 71°C. If the mass flow rate of water through the tube is 79.4 lb/min, caleulate the length of the tube.
CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.
What happens to steam pressure and velocity in a diverging nozzle?
Thank you so much can you hand write clear please
100 C² saturated steam enters the turbine Vapour at 6 MPa and Sahared liquidenters the pump at apressure of 0.01 MPa If the Detemain as heat rate to borler is ISO MU D thermal off
What is the critical pressure of R-134a, in kPa?