A power generation plant is based on a simple Clausius - Rankine thermodynamic cycle. Max pressure = 50 bar. Max temperature = 600° C. Isentropic efficiency at the steam turbine = 0.95. x = 1 at the exit of the steam turbine. Calculate: The total specific heat supplied. The specific heat supplied for the vaporization. The thermal efficiency of the thermodynamic cycle. Cranta the hs diogrom of the thermodunamie cve

A power generation plant is based on a simple Clausius - Rankine thermodynamic cycle. Max pressure = 50 bar. Max temperature = 600° C. Isentropic efficiency at the steam turbine = 0.95. x = 1 at the exit of the steam turbine. Calculate: The total specific heat supplied. The specific heat supplied for the vaporization. The thermal efficiency of the thermodynamic cycle. Cranta the hs diogrom of the thermodunamie cve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
In an ideal Rankine cycle the boiler pressure is 10 MPa. All components are operating at steady state and adiabatically. The steam enters the turbine at 550oC. The condenser pressure is 15 kPa. Determine the cycle efficiency.Find the entropy generation for the condenser for 6 kg/min mass flow rate of steam. This is a Thermodynamics question. Please explain all steps and write nicely. Thanks.
2. In a reheat cycle steam enters the high pressure turbine at 40 bar and 400°C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400°C. This steam is expanded isentropic ally in the low pressure turbine to the condenser pressure of 0.1 bar. Calculate the thermal efficiency and steam consumption for 10 MW output.
A power plant using a Rankine power generation cycle and steam operates at a temperature of 81.25°C in the condenser, a pressure of 5 MPa in the boiler and a maximum boiler temp of 775°C. The cycle operates at steady state with a mass flow rate of 2.5kg/s. Use the steam tables in the appendix of Sandler (p. 917 to 925). a.) Draw out the cycle, calculate the work required for the pump, the work output by the turbine, the heat into the boiler, and the heat out of the condenser. b.) What is the efficiency of this power plant? c.) If the turbine was only 89% efficient but still adiabatic (only generates 89% of the calculated work from part b), what is the overall efficiency of the cycle?
Rankine Cycle (Thermodynamics) Show the illustration diagram and complete and step by step solution.
Problem 3 (activity) A regenerative steam turbine has a throttle pressure of 3.8 MPa at 380°C and a condenser at 0.01 MPa. Steam are extracted at the following points: 2.0 MPa, 1.0 MPa, and at 0.2 MPa. For the ideal cycle, find (a) The amount of steam extracted (b) W, Q, and e. (c) For an ideal engine and the same states, compute (d) W, Q, and e and
Rankine Cycle (Thermodynamics) Show the illustration diagram and complete and step by step solution.
Steam is supplied to a two-stage turbine at 40 bar and 350 o It expands in the first turbine until it is just dry saturated, then it is reheated to 350 oC and expanded through the second stage turbine; the isentropic efficiencies of the first and second stage turbines are 84 % and 78 % respectively. The condenser pressure is 0.035 bar. Sketch the process on a T-s diagram and calculate; i. The work output and heat supplied per kg of steam for the plant assuming ideal processes ii. The thermal efficiency of the cycle iii. The specific steam consumption
A steam power plant work between boiler pressure (42 bar) and condenserpressure (0.034 bar). Calculate the efficiency of the cycle and specific steamconsumption for the cases:1. The plant work on Carnot cycle.2. The plant work on Rankine cycle.3. The plant work on Rankine cycle with ηiso (Turb.) = 0.84. The plant work on Rankine cycle and the steam is superheated to 500 Celicus. Neglectwork done on the pump.
From the given data, if refrigerant circulation rate is 0.025kg/s, find the refrigerant effect of the ideal vapour compression cycle.
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 3. Calculate the heat input during reheating process.
A medium size power station is used to produce 30 MW net power for arefinery. The station uses steam as the operating fluid and operatesaccording to the Carnot cycle between the pressure limits of 0.4 bar and35 bar. Steam enters the boiler as a saturated liquid and leaves it as adry saturated vapour. (i) Calculate the thermal efficiency of the power station if theisentropic efficiency of the steam turbine is 94%. (ii) State main disadvantages of using the Carnot cycle as the basis fora power station. (iii) State the name of the cycle that is used in practice in powerstations, along with three key benefits over the Carnot cycle.