Read the question carefully and give me right solution with clear calculations.  Note: pipe size required to carry the same flow rate at approximately one - third the pressure drop of the 3 in. pipe.

Q: Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water…

A:

Q: A hydraulic cylinder has these specs: Bore: 3.5" Stroke: 20" Rod diameter: 1.25" Pressure: 1800 PSI…

A: Given:D=3.5 inL=20 ind=1.25 inP=1800 psiFlow rate=4 GPM NOTE: According to Bartleyby's policy we…

Q: 4. Consider fully developed laminar flow in the annular space formed by two concentric cylinders…

A:

Q: TRUE or FALSE Pitot tube is an insertion meter. When this is located at the center, the flow that…

A: Solution is attached below:

Q: Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40…

A:

Q: What is the pressure drop in psi of 60°F water flowing through 65 ft of horizontal 1-inch schedule…

A: Consider the solution below

Q: ( Use nomograph AND the formula) Size a pipe that will not exceed 48' of HL in 6000 feet of pipe at…

A: Given data: Head loss, HL = head loss due to friction, Hf= 48 ft Length of the pipe, L = 6000 ft…

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: What is the velocity as measured by an orifice plate (0.06-m diameter) in a 0.305-m-diameter pipe…

A: Given that ,  d1=0.305md2= 0.06m∆P=75150Pa       =75.150kPa

Q: Calculate the pressure drop across a fully open angle valve placed in 5-in Scheduled 40 steel pipe…

A: To find: The pressure drop across a fully open angle valve. Given: The rate of heat transfer Q=847…

Q: 8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter…

A: given data; ⇒flow rate (Q)=10gpm=6.309*10-5m3/s⇒piston diamter (d1)=7 in=0.1778m⇒rod diamter(d2)=5…

Q: A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a hole in…

A: Consider the water level in the tank at instant t as h as shown. That means it takes time Here H is…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa    dA=150mm PB=325KPa    dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: ugh a 1.0 in diameter pipe is 3 GPM with a pressure drop of 5 PSI. What would the pressure drop be…

A: Givend1=1inQ=3GPM∆P1=5psid2=1.5in

Q: At a flow rate of 10 LPM, what will gonna happen if the pressure drops over 90 seconds from 0.657…

A: The flow rate given asthe time taken, pressure drop, the given pressure,

Q: Problem 3: A submersible deep-well pump delivers 745 gal/ h of water through a 1-in Schedule 40 pipe…

A: Given Data The flow rate of water is:Q=745 gal/h=0.0276644 ft3/s The head loss in pipe is:hL=10.5…

Q: 8.61 cally through a 200-fi-long, 1.0-in.-diameter drawn tubing at a rate of 0.060 ft'/s if the…

A: Given that, Length of pipe, L=200 ftL=60.96 m,Diameter of pipe, d=1 in,Volume flow rate of water,…

Q: What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the…

A:

Q: A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the…

A: Given that, Flow rate of chloride, Q=250 gpm,Pressure drop inside pipe, ∆P=0.006 lb·force/in2-ft…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given  Rate of flow of water = 7L/s 5in schedule 40 steel pipe. 2 fittings of 90o ell standard long…

Q: If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes…

A: Given:

Q: What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in…

A: Given data: For Water at temperature 20 degrees Celcius                      Flow rate = 0.015 ft3/s…

Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…

A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…

Q: The rest of the questions are thus: 4) Calculate the air temperature and pressure in the pump at…

A: Given R=287 J/kg.k= 0.287KJkg.k Cp=1.005KJkg.k y=1.4 P1= 1 bar= 100 kPa T1=298 K   Explanation:…

Q: Using the appropriate equation from Table 4.3, calculate the wall sheer stress (in Pa) in a tube 5…

A:

Q: Explain how the pressure and velocity of your fluid change as it travels through the pipe system.

A: As the fluid passes through a pipe system it posses 3 types of energy (Kinetic , Potential and…

Q: 2. In a 0.32 cm diameter pipe, motor oil passes and is released into the atmosphere with a flow rate…

A: The answer to the given question is given in below image

Q: of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c)…

A: The water flow rate from reservoir is Q2=60 gal/min×0.003785 m3 1 gal×1 s60 min=3.75×10-3 m3/sec.…

Q: Based on the layout of the water supply system, as show in Figure 1, the pressure, in psi, is…

A:

Q: Calculate the Reynolds number for 20oC water flow in a 1” nominal diameter sanitary pipe at Q=…

A:

Q: h2 =7 cm h = 3 cm Water.

A:

Q: Air at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a…

A:

Q: a pipe reducer with the pressure at A and B is 345kPa and 290kPa. the diameter at A and B is 50mm…

A:

Q: What pressure head drop will occur in 300 ft of new horizontal cast iron pipe, 4" in diameter,…

A: Given data: The length of the horizontal cast iron pipe is, l=300 ft. The diameter of the iron pipe…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.