R1 is Vs R2 The circuit shown in Figure 1 has two inputs, vs and is, and one output io. The output is related to the inputs by the equation 'io = a is + b vs' Given the following two facts: 1. The output is io = 0.45 A when the inputs are is 0.25 A and vs = 15 V. 2. The output is io = 0.30 A when the inputs are is = 0.50 A and vs = 0 V. Determine the values of the resistances R1 and R2 (4 Points) R1 = 24 0, R2 = 20 0 R1 = 24 0, R2 = 16 0 R1 = 48 Q R2 = 80 R1 = 30 0, R2 = 20 0

R1 is Vs R2 The circuit shown in Figure 1 has two inputs, vs and is, and one output io. The output is related to the inputs by the equation 'io = a is + b vs' Given the following two facts: 1. The output is io = 0.45 A when the inputs are is 0.25 A and vs = 15 V. 2. The output is io = 0.30 A when the inputs are is = 0.50 A and vs = 0 V. Determine the values of the resistances R1 and R2 (4 Points) R1 = 24 0, R2 = 20 0 R1 = 24 0, R2 = 16 0 R1 = 48 Q R2 = 80 R1 = 30 0, R2 = 20 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

R2= 2002 silicon Diode %3D 13V = DI -2v Please Constuct the Craut in more easy way and kind/y solve the fllowing thank you. With explañation plaie Find the $0llonng please * Curent through RI ( IRI xCurrent through R2 (IR2) * Curent through DEaf iDI) CUIR ¥ Voltoge Across RI (VRI) * Output * Diocde condiion Voltoge (Vo)
The purpose of the Zener diode is to maintain the voltage across the load at 9 V. The load draws anywhere from 0 to 400 mA of current. If R = 7 Ω, what is the minimum value of VS that will guarantee the circuit will work properly.
Referring to Figure , you measure the potential at the connection points R1 and R2 of 3 V. If you get a potential of 0 V at the connection point of the diode and R3, what can you do explain about the condition of the circuit?
half bridge given in the figure for the rectifier circuit; Output current and voltage waveform draw
1. LED flashlights use "white" LEDs which have a diode voltage drop of 4.0V. An LED flashlight has the circuit illustrated and will run off of several AAA batteries that have a 1.5 VDC rating. a. What is the minimum number of AAA cells are needed to turn on the flashlight. 4/1.5 = 2.65 /3 b. Would you arrange the batteries in parallel or in series? Series a. What series resistor will give the specified LED current? (67 K 70 L b. What is the power dissipated by the resistor you selected in part a? Vdd fritzing 2. In the previous diagram for an LED circuit, the power supply is a 9V battery and we are using a Red LED whose voltage drop is 2V. The specification sheet for the LED recommends that the "ON" current should be 10 milliamps. c. What is the power dissipated in the LED? R + LED V 1
1. A voltage divider provides 1 V output from 5 V input. The maximum output current is 1 mA. The resistors are chosen to provide load regulation of better than 1% over the load current range of 0-1 mA. Find the resistor values necessary for this application. What is the efficiency at full load?
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
11-A d.c voltmeter has a sensitivity of 1000 2/V when it measures half full scale in 100V range, the current through the voltmeter is: a-100mA b- 1mA c-0.5mA 12- A DVM measure....... d- 50mA peak value
1) Explain the functionality of the following circuit. Use text and "waveform" to explain.
Sy A circuit design calls a 1.5 kN resistor to have 4.7 V across its terminals. What would be the expected current? The circuit is built, and the resistance is measured at 1500 2 and the voltage at 4.7 V. What is the current through the resistor? f is ie
AsP plzzzz