Please answer all subpart I will like only for all subpart please Asap I will like it please...

Q: 1.3 Output Resistance: For Vcc higher than Vomin, calculate the output resistance Ro of the current…

A: Given the circuit: For Vcc higher than Vo,min we need to calculate the output resistance Ro.…

Q: i) Design and draw the circuit of an adjustable positive voltage regulator with output voltage range…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Draw the equivalent circuit for summing amplifier and voltage amplifier inverting  non-inverting

A: The summer and voltage amplifier circuits using both inverting and non-inverting opamp configuration…

Q: QUESTION 9 Use 2 decimal places A CS JFET amplifier has gm= 5.76 mS, with a drain resistance of 0.98…

A: First draw the small signal equivalent circuit the find the voltage gain   voltage gain = output…

Q: Identify two different practical examples of op-amp

A:

Q: ww R2 R1 0.2Vo V. R3 Vin Figure Q4(b)

A: According to question we have to   Determine the value of R1, R2, R3, and R4 (use standard resistor…

Q: a) Define the function of opamp circuit given below. b) If the voltage gain is 50 for the circuit…

A: (a)  The function of above op-amp circuit is that,it will amplify the amplitude of input signal…

Q: A fault has been inserted in the circuit. Repeat some of the measurements carried out on the RTD…

A: The answer as given below:

Q: A certain diff-amp has a differential voltage gain of 2000 and a common-mode gain of 0.2. Determine…

A: Given a differential amplifier has, Differential voltage gain, Ad=2000 Common-mode gain, Ac=0.2

Q: Q3. This question is on op-amps. (a) Comment on the differences between the values in the two…

A: The gain of the ideal operational amplifier and the input resistance for the practical operational…

Q: The Op-amp can amplify

A: The correct option along with the explanation has been provided in the following section.

Q: (IV) The figure below shows an R-2R ĎÁČ circuit 2R 2R 2R 2R 2R LR 2R 2R 2R Vour The reference…

A: A Digital-to-Analog Converter (DAC) is a device that converts digital signals into analogue signals.…

Q: In the following figure, Q, and Q2 are identical and operate in active mode. if IC1 = 9.5 lc2 then…

A: we need to find ( V1 - V2)

Q: In an integrator op-amp, the gain is ________ to frequency. a.has no effect b.directly proportional…

A:

Q: Voltage when applied at 2 inputs of Op-amp to get 0 V of output is called_voltage. O a. Output…

A:

Q: (1) A CdS cell (light sensitive resistor) is configured as shown in Figure Q1 (b) below using four…

A: For the given potential divider circuit the value of R needs to be calculated to get the output…

Q: 4. For the circuit shown in figure below, use a current mesh analysis to determine (a) the current…

A: As per our guidelines we are supposed to be answer the first three questions only.  Kindly repost…

Q: What happens to the transconductance of Q1 if the current I, of the device is decreased by a factor…

A: Right Answer option   (B) Transconductance Will be Halved

Q: The Op-amp can amplify 1. a.c. signals only 2. d.c. signals only 3. both a.c. and d.c. signals 4.…

A: The correct option along with the explanation has been provided in the following section.

Q: -Design and connect a subtractor operation amplifier circuit if the R1=R2=R3=Rf and V1=3V, V2=6V,…

A: We need to find Design the subtractor .

Q: Complete the table below and show your complete solution. Find the operation region (cut-off,…

A: Given

Q: Calculate the input impedance for small-signal equivalent circuit

A: Calculate the input impedance for small-signal equivalent circuit ?

Q: Question 2: For the amplifier shown in figure 2, if B=150 VCC-20 i. Find all DC parameters. R7…

A: We need to calculate dc parameters that is dc current and voltage for given circuit . We also need…

Q: Determine the R2value for the summing amplifier given below so that the output voltage is – 3V. R2…

A:

Q: An inverting amplifier configuration is as shown in the figure below. R, 300 kΩ Vcc +10 V R, 15 ka…

A: This is the inverting configuration of the op-amp, the reference voltage applied at the noninverting…

Q: The Op-amp can amplify

A: The correct option along with the explanation has been provided in the following section.

Q: Answer the question quecly please Electronic

A:

Q: For the ideal op-amp circuit of figure, determine the output voltage Vo. Express answer in two…

A:

Q: The figure below shows 3 suggested configurations for amplification purpose

A: The circuit diagram is given asHere we need to tell about the application of different different…

Q: A 2 V (DC) signal with internal resistance of 10 k2 needs to be amplified to drive a red LED which…

A: Given: 2. A 2 V (DC) signal with an internal resistance of 10 kΩ needs to be amplified to drive a…

Q: Q1. A series Op-Amp voltage regulator which its input voltage is 15V and to regulate output voltage…

A: Operational Amplifier: Operational amplifiers are linear devices with all of the qualities necessary…

Q: Bllowing figure, Q1 and Q2 are identical and operate in active mode. if Ic1 = 9.5 l2 V2: V2 one:

A:

Q: ........ Pressure transducer is a device that converts an input (pressure p) into an electrical…

A: The input (pressure) and output (voltage) samples of a pressure transducerU=k⋅p+a, are given as:

Q: The Op-amp can amplify 1. a.c. signals only 2. d.c. signals only 3. both a.c. and d.c. signals 4.…

A: The operational Amplifiers are direct-coupled amplifiers. Here, the coupling between the stages of…

Q: Design Question Vref Rref RG RM Al VOUT Digital Input, DIN DAC1 n VDAC Figure 1 Figure 1 shows the…

A: given now  1. voltage error due to DC offset as we can see Vio=offset voltageVB=VioVA=Vioapply KCL…

Q: Q1: a) Design the oscillator in Figure 1 to start oscillation with closed-loop gain of 8.5, then R…

A:

Photoconductive Cell

Photoconductive cells are light-sensitive resistors in which resistance is inversely proportionated to light intensity when illuminated. These devices consist of a thin single-crystal or polycrystalline film of composite semiconductor materials. Cadmium sulfide (CdS) is used to make the most commercially available photoconductive particles which are sensitive to light in the visible spectrum. Other less commonly used substances respond to infrared light, but not to the visible spectrum. Such substances are lead sulfide (PbS), lead selenide (PbSe), and lead telluride (PbTe), and so on.