........ Pressure transducer is a device that converts an input (pressure p) into an electrical output signal (voltage U). The pressure drop [kPa] across a valve in a water pumping system was measured with a pressure transducer that provides a voltage signal [mV]. Below are the results of a calibration measurement for the transducer: U [mV]p [kPa] 16 93 2 13 170 24 247 35 303 43 Your task: a) Based on the calibration measurement results, form a linear model U = K p+a for the pressure p to voltage U relationship of the pressure transducer. U = P+ Create a straight-line model in units [kPa] and [mV] b) Determine the transducer nonlinearity (in millivolts) when the transducer pressure is 27 kPa and the output signal is 193 mV. Nonlinearity is mV c) Find nonlinearity at 27 kPa as a percentage of span % of output span.

........ Pressure transducer is a device that converts an input (pressure p) into an electrical output signal (voltage U). The pressure drop [kPa] across a valve in a water pumping system was measured with a pressure transducer that provides a voltage signal [mV]. Below are the results of a calibration measurement for the transducer: U [mV]p [kPa] 16 93 2 13 170 24 247 35 303 43 Your task: a) Based on the calibration measurement results, form a linear model U = K p+a for the pressure p to voltage U relationship of the pressure transducer. U = P+ Create a straight-line model in units [kPa] and [mV] b) Determine the transducer nonlinearity (in millivolts) when the transducer pressure is 27 kPa and the output signal is 193 mV. Nonlinearity is mV c) Find nonlinearity at 27 kPa as a percentage of span % of output span.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load: a = 90° a. Sketch the output voltage waveform. a b. Determine the ripple factor. VA= 240 V RL 752 CB A-B A-C B-C B-A CA C-B a Vc 27
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load: a. Sketch the output voltage waveform. a = 30° b. Determine the ripple factor & input power factor. VA= 240 V(V) VB RL 2202 2n
1. Connect the circuit shown in Figure (1), the power supply is set to zero volts. 2. Measure and record in table (1), the forward current in the diode at each level of voltage (Vf). 3. Determine the forward resistance Rf = Vf /If. A I KO E (0-4) V. Figure (1) Vr 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Ir R Table (1)
Design a full wave rectifier based on the circuit shown in Figure 5 below: N: N2 D3 RL ww US D, Figure 5 The required specification for the full wave rectifier circuit includes the peak output voltage of 5 V, deliver 100 mA to the load R1, and produce an output with a ripple of not more than 5 percent. An input line voltage of 220 V (ms), 50 Hz is available. Given V, =0.7 V. (d) Calculate v, (max). (e) Find the required turn ratio for the transformer. (1) Determine the Peak Inverse Voltage (PIV). (g) What is the effective load resistance? (h) Determine the required capacitance of the filter capacitor.
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 162 V and the firing angle of the SCR is 60 degrees, the peak voltage of the input sinusoidal would be: O A. 197 V O B. 228 V O C. Can't tell; need more information. O D. 340 V O E. None of the other choices are correct
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
#4(a) An 8.2 V (8.2 V at 25 °C) has a positive temperature coefficient of 5.4 mV/°C. What is the output voltage if the temperature rises to 90° C? Page | 4 b) Name two applications of the Zener Diode
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
A three-phase half wave rectifier is operated from a 3-phase, 230 V, 50 Hz supply with load resistance R = 10Omega Find the value of firing angle if an average output voltage of 60% of the maximum possible output voltage is required. Derive and draw the output voltage at a>30