R1Click here for image↑ ) 111+Rm/↑) 2In this circuit, R1 = 5 Q2, 11 = -6 A, 12 = 2 A, Rm = 8 Q. / has units of amperes.Determine the Thevenin equivalent circuit at terminals a-b.aCOState the values of the open-circuit voltage, Voc (in volts), and the equivalent resistance, Rth (in ohms), in the box below. Round your answers to onedecimal place.

We need to find out the thevenin equivalent circuit for given circuit

R1 Click here for image 11 1+ Rm/ 12 In this circuit, R1 = 50, 11 = -6 A, 12 = 2 A, Rm = 80. / has units of amperes. Determine the Thevenin equivalent circuit at terminals a-b. be State the values of the open-circuit voltage, Voc (in volts), and the equivalent resistance, Rth (in ohms), in the box below. Round your answers to one decimal place.

R1 Click here for image 11 1+ Rm/ 12 In this circuit, R1 = 50, 11 = -6 A, 12 = 2 A, Rm = 80. / has units of amperes. Determine the Thevenin equivalent circuit at terminals a-b. be State the values of the open-circuit voltage, Voc (in volts), and the equivalent resistance, Rth (in ohms), in the box below. Round your answers to one decimal place.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Q2: A PMMC(Galvanometer instrument) has a resistance of 10052 and FSD for a current of 400Au. A shunt arrangement is shown in order to have an multi-range ammeters(AYRTON). Determine the various ranges to which the ammeter may be switch. Assume the R1-R2-R3-R4-0.00152. PMMC 10052
Estimate voltage E2 when E1=90sin2400t V, R1=R2=20 ohms, L1= L2=3mH and M=0.15mH
%3D ) Drurde (l0o1102 and (o
6) QJ what is the Stefresfonse of overdlam fed and underdamfed Systems when alerdamfel $1) and underdamfed d Cos Ś s) て(S) - Step Wn Wn (stWn)" resfonse
What is the difference between the cut-off voltage VGS0 f and the narrowing voltage Vp? Explain this with the diagram
this question is related to subject ELECTRONICS DEVICES AND CIRCUITS . solve this question on A4 page manually with step by step clearly. kindly send with in 30 mintues. thanks.
Part A: A multi-range ammeter is required to measure the current in a certain network. A PMMC instrument has connected as an Ayrton shunt with a four resistor across PMMC. The resistance values are R1 = 0.0060, R2 = 0.0650, R3 = 4.00 and R4 %3D =10.00. The PMMC has Rm = 1kQ and FSD = 50µA. %3D a. Draw the circuit for the multi-range Ayrton shunt. b. Calculate the four current ranges of the ammeter. c. What is the main advantage of Ayrton shunt ammeter compared to parallel type. d. Briefly explain how this device can be calibrated. * Note: Show all calculation details. Part B: The measurement of the voltage from a prototype of a 20V DC power supply were captured by 8 times as shown in the following table: Number 1 6 Voltage (V) 18.5 19.8 20.2 19.9 20.0 20.1 19.7 18.9 Determine the following: 1. the arithmetic mean, 2. the standard deviation of the readings, 3. the probable error. 4. If the voltmeter that used to carry the measurements has an error of 0.5%; calculate the total error in…
Q4
Please answer it with clean and step by step solution. This subject is Electronics specifically. Thank you and keep safe.
H.w For the circuit show n figure ca Iculate the expre ss ion of tne assume t he in i tial value of in ductor .initial value of cap acit or is zero o'lf th o'5 F
For the circuit in the figure, draw the equivalent circuit and values I1, I2 and ID1, ID2.find? need handwritten only ,otherwise downvote.)
150 100 + VA- a -4V AVA -7V 81. B b Figure 2 shows a simplified model of a gas-discharge lamp. One characteristic of these lamps is that they exhibit negative resistance; in other words, as current increases the voltage drops further, making such lamps inherently unstable. As such, a current-limiting ballast is required. For the connection shown in the figure: 1. Find the equivalent Thevenin circuit of the lamp. 2. Find the ballast resistance needed to limit the current drawn from a 24-volt source to 6 amperes.