sir solve the problem related to ic engine subject i. The following particulars were obtained during a trial on 4 Stroke Gas Engine, which lasted forone hour. The speed was 15000, brake load was 1500 N, the IMEP was 10 bars, calorific valueof fuel is 20 KJ/litre, brake circumference was 4m and the missed power cycles were 500. Thebore and stroke were 30cm and 50cm respectively. The fuel consumption was 20000 litres. Thecompression ratio is 8. Determine IHP, BHP, ISFC, BSFC, Brake thermal efficiency andRelative efficiency.

Givenspeed n=15000brake load b=1500NIMEP =10barcalorific value cf=20kJ/ltrbrake circumference…

Answered: r solve the problem related to ic…

Engineering

Mechanical Engineering

r solve the problem related to ic engine s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal…

A: Input speed of belt N1=1750rpm, Output speed of belt N2=725rpm,Belt Linear VelocityVb=4000ft/min…

Q: Q: Ahydraulic servomotor system is shown in Figure, Determine the overall block diagram of the…

A: A hydraulic servometer system is shown in figure To determine the overall block diagram of the…

Q: DH table for WLKATA robot

A: Explanation of DH Parameters:θi (Joint Angle): This parameter represents the rotation about the…

Q: Find the average piston velocity (between limiting positions) for an in-line slider-crank mechanism.…

A: Let L= Length of stroke l=length of crank N=3000rev/min as we know L=2l=4inch

Q: Explain the types of compressors used in R&AC system considering the principle of working and…

A: The compressors are one of the most important parts of the refrigeration cycle. The compressor…

Q: The throttle opening is electronically controlled; the position When the throttle is fully open,…

A: Given Engine setup To find Role of Air filter Air temperature sensor Intake manifold (tumbler) valve…

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: Derive the swing equation to describe the rotor dynamics and extend this for explaining the…

A: Consider the diagram shown below, The expression fro the angular pisition of the rotor is given…

Q: Q1. An open belt drive configuration having 10 pulleys in total, the input and output speeds are 20…

Q: 10. In instance. Therefore high system accuracy is achievable. 11. feedback devices closely monitor…

A: 1.In Closed loop feedback devices closely monitor the output and any disturbance will be corrected…

Q: As Becky was driving "Old Betsy," the family station wagon, the engine finally quit, being worn out…

A: These questions are based on the concept of engines and revolution.

Q: give 10 Troubleshooting for IC engin

Q: Q5. Explain the actual Indicator and valve timing diagrams for a Four Stroke Cycle Diesel Engine.

Q: Q : The ciank and connecting rod of steam engine O:Sm and 2:Sm aue long. The counter clock-wire…

Q: Discuss the Volumetric Efficiency as performance parameters on the speed of an IC engine. 39.…

A: what is volumetric efficiency? Volumetric efficiency is a type of internal combustion engine style…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

sir solve the problem related to ic engine subject

i. The following particulars were obtained during a trial on 4 Stroke Gas Engine, which lasted for
one hour. The speed was 15000, brake load was 1500 N, the IMEP was 10 bars, calorific value
of fuel is 20 KJ/litre, brake circumference was 4m and the missed power cycles were 500. The
bore and stroke were 30cm and 50cm respectively. The fuel consumption was 20000 litres. The
compression ratio is 8. Determine IHP, BHP, ISFC, BSFC, Brake thermal efficiency and
Relative efficiency.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW Find the Volumetric efficiency
The following data refers for the single cylinder 4 stroke diesel engine. The brake power is 73 kW and engine speed is 500 rpm. The break mean effective pressure is 8 bar and mechanical efficiency is 80 %. The BSFC of the engine is .30 kg/kWhr of the fuel calorific value of 43200 kJ/kg. Determine indicated thermal efficiency.
Engine Type Four cylinder Four stroke MPFI petrol engine(Maruti Zen), Bore: 0.072 m, Stroke: 0.061m Capacity: 993 cc, Power: 60 HP at 6000 rpm, Torque: 78.5 Nm at 4500 rpm and Compression Ratio :9.4:1. Explain how to calculate :- (1) Mechanical Efficiency (2) Brake Thermal Efficiency (3) Indicated Specific Fuel Consumption
an engine burns a liter of fuel each 12 minytes, the fuel has specific gravity os 0.8 and heating value of 45 kj/kg. the engine has an efficiency of 25%. what is the brake morse power of the engine?
1. A four stroke diesel engine gave the following test results at a speed of 450 RPM. Mean effective pressure - 850 kPa Cylinder bore - 22 cm. Stroke - 26 cm. Specific fuel consumption - 0.32 kg/BHP.hr Calorific value of fuel – 45000 kJ/kg. Mechanical Efficiency = 88% Determine the (a) BHP, (b) IHP, (c) Indicated themal efficiency, and (d) Brake thermal efficiency.
this answer i need relative efficiency =62.95 only dont send wrong solution
Q78 A four Cylinder, four stroke Petrol engine has a Compression ratio of 6 to1. A test on this engine gave the following resultsg Net brake load = 20kg, effective brake arm = 0.5 m, indicated mep =6alo N/m, engine speed 2400 rpm, %3D fuel consumption = lo kg /h, calorific value of the fuel = 44000 kj (kg, Cylinder bore 86 mm, engine stroke -l00 mm. Calculates @the mechanicalefficiency the brake thermal efficiency the relative efficiency assuming the engine works on the Constant volume cycle and that 8 - 1,4forair The brake mean effective pressure.
Please answer
Show Complete Solution
Question Design a 4 cylinder inline, turbo diesel engine to produce 103 kW of brake power at design speed when installed in a Multi-Purpose Vehicle (MPV). The square engine operates on a four stroke cycle and produces 20 bar of maximum brake mean effective pressure (bmep). Average piston speed is 11.5 m/s and bmep at peak power is 14.4 bar. If the decided values of torque position and torque increase are 50% and 28% respectively, determine the: a) bore b) stroke c) displacement d) maximum torque e) engine speed at peak torque as well as f) engine speed at peak power
Fuel consuption of a engine is 0.35 kg/ KW-hr and heating value of fuel is 43000 KJ/kg. The brake thermal elliciency is (a) 20.1% (b) 23.9% (C) 28.29% (d) 32.21%