A single-cylinder, four stroke cycle Cl engine with 12.9cm bore and 18cm stroke operating at 800rpm, uses 0.113kg of fuel in 4 minutes while developing a torque of 76N-m. Calculate (show your solution): a. Brake specific fuel consumption (gm/kW-hr) b. Break mean effective pressure (kPa) c. Break power (kW)

Q: 1. A cylindrical container gromm in diameter, 2 meters long is to be filled with methane gas, 16°C.…

A: Dear student,                     According to the guidelines, I am allowed to answer only one…

Q: Evaluate Hot chamber pressure die casting process with a help of neat sketch.

A: Hot Chamber Pressure Die Casting

Q: 10 Fig. (6) 8 MPa

A: Given Dataσx=8MPaθ=24°

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: Please use maximum shear stress theory

A:

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

A: The basic purpose of the lubricating any moving part is to reduce the friction between the parts and…

Q: How we can measure shear modulus?

A: The earth's material reaction to shear deformation is measured in shear modulus. The ratio of…

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

A:

Q: Do most of the columns have residual stress? why?

A: When the columns or any member are under no loading condition, and there are stresses present inside…

Q: List 10 materials of a windmill.

A: Wind mill: It is mechanical device which convert the kinetic energy of the air into the mechanical…

Q: Find the welouty Slay A=2.1m2 of S. - २० ms %3D

A: Given data : Area of channel A=2.1 m2 Discharge through channel Q=20 m3/s   To find : Velocity of…

Q: A certain type of cans are formed on a machine by spinning them from cardboard stock and attaching a…

A: Given \ Sample size N=50 Total number of samples is M=30 Table1: Number of nonconforming cans in a…

Q: Describe the stress involved in an unopened bottle of pop.

A: Solution:

Q: What is the minimum pressure required to reduce volume of a brass sphere by 0.00003 %?

A: Given:reduction in volume=0.00003%

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: The general specification for production tubing is

A: After the casing has been run and cemented in place, production tubing is run into the drilled…

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: Industrial pipes Expansion joints are fragile elements and therefore should be avoided…

A: The objective of the question is to understand when to use expansion joints in industrial piping…

Q: State an equation of vertical pressure in uniformly loaded rectangualr area ?

A: given:   State an equation of vertical pressure in uniformly loaded rectangualr area ?

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: -450.76 for parts (c) and (d) are incorrect.

A: To determine:c)The gauge pressure at point 2d)The gauge pressure at point 3

Q: Q3. What is "Hardness" and how it can

A: ◆The hardness is defined as, "the ability of the material that can resist indentation or scratch or…

Q: reate an acceptable temperature and relative humidity range for your working area.

A: The moisture content (i.e., water vapour) of the atmosphere, represented as a percentage of the…

Q: we didn't use viscosity value. Won't we use? And thank you for your

A: Viscosity is the resistance between the layers of the fluid which further causes the shear stress in…

Q: How can I make a force table similar to this one but with adding one more component of tension so…

A: In this problem, it is asking how to balance the two forces in the given table.

Q: Circle all correct statements for the Young's or elastic modulus, E: a. Has units of force per unit…

A: As per our guidelines, we are supposed to answer only first one question in case of multiple…

Q: How did you get the temperature 367? What is the solution?

A:

Q: explain the procedure to handlethe cast resign?

A: Resin casting: It is a method of plastic casting where mold is filled with a liquid synthetic resin…

Q: Maximum Stresses in Thick Walled Cylinders

A: To determine the maximum radial and tangential stress for the thick walled cylinder

Q: DIFFERENTAITE SHEAR STRESS FROM SHEAR STRAIN. THEIR RATIO

A:

Q: Q.Define the slip and show the effect of slip on velocity ratio.

A: SLIP Pulleys (driver/driven) and the band are defined as inadequate frictional grip. Slip is the…

Q: 10- Cast Structure are: Chill Zone, Columnar Zone and equlaxed Zone O True O False

A: The given statement is true.

Q: Write the nature of work done by an elongated spring?

A: The elongation produced in an ideal spring is directly proportional to the spring force F=−kx.

Q: 4. Briefly describe die casting process and name 2 types.

A: die casting method  the die casting are also known as pressure die casting and are defined as that…

Q: In a well constructed paragraph define the material requirements for a single-use (disposable) water…

A: Single use water bottle :A water bootle is used to contain the water and use at any time when we…

Q: Dari gambar di atas gambarlah diagram bebas untuk semua batang. Kemudian carilah gaya reaksi tumpuan…

A: Given data  Given foce system.