Question2: At a temperature of 308 K, a certain junction diode has in = 0.1 mA for vD = 0.6 V. Assume n = 1. Find: a) Saturation current Is b) Diode current ip at vD = 0.65 V c) Diode current ip at vp = 0.7 V Use the following diode equations: vp ip = Is[e nvF) – 1] kT Vr ==;k = 1.38X10-23J/K;q = 1.6X10-19coulomb

Question2: At a temperature of 308 K, a certain junction diode has in = 0.1 mA for vD = 0.6 V. Assume n = 1. Find: a) Saturation current Is b) Diode current ip at vD = 0.65 V c) Diode current ip at vp = 0.7 V Use the following diode equations: vp ip = Is[e nvF) – 1] kT Vr ==;k = 1.38X10-23J/K;q = 1.6X10-19coulomb

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the suitable values for resistors R3 and R4 for the regulator in Figure Q4.d. The required output voltage is 7.4V, and the Zener diode voltage is 4.7V. V₁ Ď R₁ R₂ Τ1 R3 H 21 T2 Vp R4 Vz Figure Q4.d V.
For a diode connected NMOS, determine the required drain to source voltage (in V) to produce a drain current of 9.41 µA. Assume the following specifications for the NMOS: k = 6.91 µA/V2, W/L = 7, VTH = 0.9 V, LAMBDA = 0 V-1. Express your answer using 3 decimal places.
From the diode circuit shown below. If E=40 V and RL=400, determine the current supplied from the battery. the voltage across the load resistance. and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 2 0. RL E= a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
In this Zener diode regulator, the source voltage varies from 6 V to 10 V. Assume that the load current varies between 2 mA and 33 mA, and that the diode is an ideal 3 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
Question 4
In this Zener diode regulator, the source voltage varies from 8 V to 10 V. Assume that the load current varies between 2 mA and 45 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures.
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
Calculate the current (I) through the diode and voltage across the resistor (Vout). Assume V1 =15V,R1=6KN. Ge Vout V1 R1 Diode D1 is ON or OFF? Choose... Vout= Choose... Current (I) = Choose... v
The Zener diode shown below, is specified to have Vz-20V at Izr, IzK = 0.1 mA, IzT =17 mA, and r, = 14 2. Voc = 30V. 1) Replace the Zener diode with its Model. 2) Find the current I with no Load. 3) Find Vo with no Load when VCC = 30V. 4) Find R1 Min. r30V 2000 Vz = 20V %3D 68-V zener
A central station is setup up for simultaneous monitoring of 10 hospital patients. The data from the 10 patients are brought to a processing center over wires and are sampled, quantized, binary-coded, and time-division-multiplexed. The multiplexed data are transmitted to the monitoring station as shown in the figure below. The bandwidth of the signal received from each patient is 200 Hz. The maximum acceptable error in sample amplitudes is 0.5% of the peak signal amplitude. The sampling rate must be at least twice the Nyquist rate. Determine the sampling rate, the number of levels, the number of bits per level and minimum cable bandwidth needed to transmit the data. Processing center Cable Receiver (14)
A PN Junction diode gives a current of 50 mA at a room temperature of 20°C when the forward bias voltage is 200 mV. Determine a) the saturation current with a negative bias, b) the diode current when room temperature is 30°C and c) the diode current at a forward bias voltage of 300 mVolt and 30°C. [4]
In a Simplified Diode Model, up to the barrier potential or Vdiode the current through the diode is increasing. Select one: True False