QUESTION.1. A square plate in the x-y plane is situated in the space defined by –1 m < x < 1 m and –2 m s y< 2 m. Find the total charge on the plate if the surface charge density is given by Ps = 15x²y* (µC/m²). Solve the question by clearly writing all steps of mathematical operations with correct notation and specifying all formulas and units.

Q: A mass is connected by a spring and damper to the wall as shown in the following figure. The floor…

A: In this question,  We need to calculate the transfer function of the given system.  We are solving…

Q: could you help me please it's one question

A: NOTE :- According to our company policy, experts can answer only 3 subparts at a time. So please…

Q: I understand the process but looking at my written work where did i make a mistake? How do i fix it?

A: We need to point out the incorrect steps in the given solution in order to find total resistance of…

Q: use both IEC and NEMA symbols. - Conductors crossing but not connected - Conductors crossing and…

A:

Q: Match V1(s) and V2(s) to the appropriate graphs of v(t) on the following page. 90 100 v1(s) V2(s)…

A: The single in time domain for 1st function is calculated by taking the Laplace inverse of the signal…

Q: Question1: What device function is realized by this circuit given below? D Wo S W₁ D

A: The question is about finding output of the gates.The output of given circuit is similar to the 2×1…

Q: 1. Work on the three Sub parts of the problem below using the explanation steps from the part of the…

A: Current Transformer 1) It is used to measure High current. 2) It is connected in series with the…

Q: 1. If this were a real circuit, what would be the sources of experimental error? (Remember…

A: In any examination including flows there are numerous potential wellsprings of mistake, here are a…

Q: f(t) M fricfionless surfaće X = 0 f(t) M frictionless surfaće С. x = 0 f(t) M frictionless surfaće…

A:

Q: What is the scientists trying to solve these problems?

A: The question deals with overcoming the disadvantages of perovskite solar cells.

Q: A variable resistor enables one to change the resistance. One design involves a horizontal tube of…

A: Given wire diameter (d) =1 mm tube radius =R =2.5 cm   Change in resistance Rchange =3 ohms

Q: How do you solve equation 2 and 3? I can't come up with that answer?

A: here we are asked to solve equation 2 and 3 only.

Q: . A solar cell can be approximately modeled by the linear circuit in the Figure at right. a) Suppose…

A: Given:a solar cell approximate model,To do:a) If two identical solar cells are connected in series…

Q: Okumura model is applicable for distances of

A: The solution is provided in the following section:

Q: Silicon is doped with 3 x 1018 arsenic atoms/cm³ and 8 x 1018 boron atoms/cm³. (a) Is this n- or…

A: We need to tell about type of semiconductor and hole and electron concentration for given…

Q: Design a BCD to gray code converter and implement using PLA

A:

Q: Say that you are given some TPWM and some number of intervals N to specify TON. If TPWM doubles…

A: PWM -Pulse width modulation is a technique that varies the ON/OFF time of a waveform. T PWM =The…

Q: In a balanced three-phase system, the source is a balanced Y with an abc phase sequence and a line…

A:

Q: Five devices are connected as shown in Figure 1. The current i+(t) and voltage vs(t) are plotted in…

A: Five devices are connected as shown below: The current i1(t) and voltage v3(t) are plotted in the…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.