Question: The project flow rate determined according to the stream yield will be transmitted through a rectangular channel in the shape of Q = 10 m3/s. The Manning coefficient was determined as n = 0.04 according to the covering material of the channel and the longitudinal base slope of the channel was determined as 10 = 0.0015 according to the topographic characteristics of the land. Determine the channel bottom width (B) and flow depth (h) with the concept of the most appropriate cross section.

Question: The project flow rate determined according to the stream yield will be transmitted through a rectangular channel in the shape of Q = 10 m3/s. The Manning coefficient was determined as n = 0.04 according to the covering material of the channel and the longitudinal base slope of the channel was determined as 10 = 0.0015 according to the topographic characteristics of the land. Determine the channel bottom width (B) and flow depth (h) with the concept of the most appropriate cross section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil Engineering 1. A main irrigation canal with a bed width of 2.5 meters and a side slope of 1.5 vertical, 2 horizontal is to be constructed at a uniform land slope/gradient. The capacity of the stream is 35 m³/s. If n=0.025, determine depth and the slope of the land. Show the full solutions and formula used.
All information given... Please solve clearly
As a result of the construction of a 4 m high bridge over a rectangular stream with a width of 8.6 m, the width of the stream under the bridge decreases to 5.8 m. In case of a flood flow of 132 m3/s in this stream, the roughness value of the Stream Manning was determined as 0.014 and the slope as 0.011. a. Calculate the uniform water height and regime of the flood current. b. Determine whether the bridge will be submerged as a result of the flood current.
A trapezoidal channel having side slopes of 1:1 and bed slope of 1 in 805 is required to carry a discharge of 0.001242 m3/min. Find the dimensions of the channel for minimum cross-section. Take Chezy’s constant as 50.
A triangular threshold is used to control the water depth which tends to be constant upstream of an open channel. Water flows on a V-notch weir with = 90^o and the magnitude of gravity is 9.81 m/s^2. What is the water discharge upstream of the threshold when conditions are normal with a water level of 0.24 m and during a flood with a water level of 1 m?
Please solve quickly For an irrigation project, you need to design an irrigation channel to convey water with a given flowrate. The water depth in the channel is 1.5 m. The channel has a trapezoidal cross-section and its slope is J0=0.001 and its roughness coefficient is n =0.015. Determine the base width of the channel in m.
An irrigation canal is to be designed for a discharge of 40m³/s with ground slope of 1.5×10. The bed material has a size of 2mm. Calculate the dimensions of the canal. What would be the dimensions of this canal if it was to be designed on the basis of Kennedy method with C.V.R equal to 0.85. Bazin coefficient 1.5 and the ratio of bed to depth of the canal is the same as obtained above.
Subject : Fluid mechanics Determine the normal depth (m) in a rectangular channel with flowing discharge of 90 m3/s, roughness of n=0.025, slope of 0.001, with bottom width of 6 meters.
A 4 m wide rectangular channel, having bed slope of 0.001 carries a discharge of 16 m³/s. Considering Manning's roughness coefficient = 0.012 and g = 10 m/s², the category of the channel slope is:
For a V-shaped concrete lined channel with total included angle of 80°, and a depth of 3 m if the discharge is 10.7 m^3/s. Determine the slope if Darcy-Weisbach constant is 0.011 (Your final answer shall be in fraction i.e. 1/5000). Show a diagram.
Civil Q- An irrigation canal has been designed to have R = 2.5 m and S = 1.6 x 104. The sediment on the bed has a median size of 0.30 mm.Determine the amount of bed load using Einstein's method.Assume depth of flow and mean velocity of flow to be 2.8 m and 0.95 m/s, respectively.