6 1 2 4 3 6 9 7 Dimensions in the figure are in meters. With the given dimensions and Manning coefficients, determine the channel's flow rate and the channel's effective Manning coefficient. Water is flowing on a channel whose bottom slope is 0.002. The cross-section of the channel is shown in the figure. The channel has an unfinished cement surface (n = 0.014) at subsections 1 and 2 and a light brush (n = 0.05) at subsection 3. 6 6 6 9

6 1 2 4 3 6 9 7 Dimensions in the figure are in meters. With the given dimensions and Manning coefficients, determine the channel's flow rate and the channel's effective Manning coefficient. Water is flowing on a channel whose bottom slope is 0.002. The cross-section of the channel is shown in the figure. The channel has an unfinished cement surface (n = 0.014) at subsections 1 and 2 and a light brush (n = 0.05) at subsection 3. 6 6 6 9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following cross-sectional areas (m2) are calculated for centre line of a drain trench at 5 m interval 2.5 2.7 1.8 3.5 3.7 2.9 2.8 1.6 1.1 V=d[(first+last)/2)+ sum of rest cross-sectional areas] Trapezoidal formula The calculated volume in m3 of the material for the trench is; Select one: O a. 111.4 O b. 113.0 O c 104.0 O d. 118.0 O e. 34.2 Of. None of the given answers
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.
determine the magnitude of the differential sticking force across a permeable zone of 30 ft in thickness using the following data: Differential pressure =500 psi Area of contact is 20% Filter cake =1/2 in (12.7mm) friction fractor=0.1 Drill pipe:5
The velocity of flow from 3 cm of the wall of a pipe is 30% more than the velocity of flow from 1 cm of the wall. If diameter of the pipe is 8 cm, determine the average height of roughness.
if the median size of bed material of a natural channel is 1.2 mm, then the Manning's n coefficient for the channel is about 0.027 .a 0.041 .b 0.012 .C 0.035 .d
for the following conditions, determine the groundwater infiltration. new two lane highway, lane width 12ft; shoulder width 10ft; length of crack 20ft; rate of infiltration 0.5ft^3/day/ft^2; spacing of crack 25ft kp=15*10^-5 ft/day
The observed pressure drop for 40 °F water flowing at 16 ft/min in a 4.5-in-diameter pipe is 9.68 x 10 psi/ft. Determine the relative roughness (e/D)of the pipe. (e/D) =
please show written complete and clear solution
Show complete and clear solution with pressure diagram thank you
The length of the levee perpendicular to the paper is 600 m; the sand on top and bottom have k1=750 ft/day and k2= 40 in/s respectively. The thickness of sands is equal, m = 670 m, n=575 ft, B = 8ft, C = 525 ft. Determine the amount of water flowing to the ditch in in3/min. (See picture below)
A mechanically cleaned bar rack screen is installed ahead of a velocity controlled grit chamber. The bars are 10 mm thick, and the openings are 20 mm wide. The flow through the screen is 0.75 m3/s, and the depth of flow is 1.45 m in the channel upstream of the bar rack. 1. Calculate the flow velocity through racks (m/s). 2. Calculate the water depth in the channel downstream of the bar rack (m).
b) A pipe bend has a non-dimensional wall roughness value of e/D = 0.0002. The flow through this bend is highly turbulent. If the pipe bend has an equivalent length of Leq/D = 15, determine its resistance coefficient K.