Question- The capacity of a single ISA 100 x 100 x 10 mm as tension member connected by one leg using 6 rivets of 20mm diameter is (Allowable stress is 150 N/mm²).

Q: Which products are semi-finished steels. I. Bloom II.Bars III.Rods IV.Billet V.Slab VI.Plates

A: Semi-finished steel is intermediate steel which is formed by casting liquid steel or by rolling and…

Q: ne and discuss the two metnods used in the design of steel m

A: ASD Method:- WSD, also known as ASD, is a conventional approach of structural design that applies…

Q: Compute for the linear weight of a 32mm diameter reinforcing bar. (Use the Unit weight of the Steel)…

A:

Q: What will be the block shear strength of a tension member as shown in figure below? The steel is of…

A:

Q: A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below.…

A: Answer We are given  Plate 1/2 x 8 bolt diameter  = 1 in A36 steel Shear lag factor U = 0.1

Q: It is acceptable to have threads in glass parts as long as such threads were coarse.   T or F

A: Threaded glass components are manufactured by a number of different companies in a variety of sizes…

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: b). Determine the COMPOSITE centroid of the T section. (x, y shown is the origin and the reference).…

A: It is required to find the composite centroid of the T section.

Q: 9-D20 Two steel plates (E = 30 E6 psi) are glued to the pine beam (E = 1.8 E6 psi). The maximum…

A: Shear Stress = Shear load/affected area = 20000 lb / 16x10 =125 psi

Q: Determine:  Ix & ly = Moment of inertia about axis XX and YY Rx & Ry = Radius of gyration about…

A: For W 250 x 22 Ix = Moment of inertia about xx axis Iy = Moment of inertia about yy axis Rx = Radius…

Q: The wood members A and B are to be joined by plywood splice plates that will be fully glued on the…

A:

Q: O Based on bolt capacity in shear. O Based on bolt bearing capacity. ® Based on block shear strength…

A:

Q: Thursday Nov.24, 2020 Compute the design strength in tension, Pn, of an ASTM F1554 Gr. 36 % in…

A: Compute the design strength in tension Pn, of an ASTM F1554 Gr. 36% in diameter THREADED rod.Your…

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75…

A: We will use formula of Net area.

Q: An A36 tension plate is 9 mm thick is given below.  Bolts are 20 mm.  Given that s = 50 mm and g =…

A: Given data in question  Thickness of plate Diameter of bolt Bolt lines Guage distance  To find out…

Q: a. Under a heavy vibrating loads it is possible that a fully tensioned bolt may come loose. As a…

A: Under heavy vibration or dynamic loading bolted connections and welded are not preferred. Because…

Q: If a rolled steel flat designated as 55 ISF 12 mm is used as lacing, then minimum radius of gyration…

A: Given, 55 ISF 12 section with thickness, t = 12 mm   To find = Minimum radius of gyration

Q: steel section. Check web yielding and web crippling if the steel used is ASTM A992, grade 50.

A: Solution: For W18×50, we obtain the following properties from ASTM, Below are the structural steel…

Q: The board in the image below is most likely ... O a. O b. quarter sawn O c. through sawn rift sawn

A:

Q: THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!…

A: Solution: Given: Diameter of rivets = 16 mm Thickness of gusset plate = 20 mm Allowable Bearing…

Q: What are the uses of tension and compression steel members?

A: Steel is notable for giving design and strength not at all like some other with regards to…

Q: choose the W section of 50 ksi steel

A:

Q: what is the advantages of SAP and stadd in steel design

A: SAP and STAAD are both software tools which are commonly used in structural engineering for both…

Q: Which of the following is the most efficient column section? O Pipe Wide Flange Square tubing O…

A: Brief concept- Column Section- It is a structural member that helps in transferring the compressive…

Q: A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is…

A: Area of the angle = 2736 sq.mmallowable shear= 150 MPaFt= 0.6FyFy= 250 MPa

Q: m alone)? (Assume bending arour

A:

Q: A butt joint shown in figure 3.29 is bolted using A 325 bolts with a diameter of 22 mm, with threads…

A:

Q: NOT TO Scale TU 760lbs Iff 120 lbs 3ff b Truss, frame "cale member forces & id tension o compressi…

A: Determine the members force of the truss. Let's solve using method of joints.

Q: Give the formula for the tensile and shear strength of the weld joint. Explain the various terms in…

A: Need to definethe formula for the tensile and shear strength of the weld joint

Q: Q- IF THE LENGTH OF THE WELDED JOINTS FOR TWO PLATES IS 700 MM FOR A PLATE OF 8 MM AND 10 MM WELDED…

A: Given- Length of welded joints=700 mm,plates thickness 8 mm & 10 mm,weld size= 6 mm. It is…

Q: Define and discuss the two methods used in the design of steel members. What are the advantages and…

A: To answer No. 1

Q: A 10-foot long, 12-inch wide and 2-inch thick plate will weigh? (use steel density of 490 lbs/cft)

A: Here the formula p=MV p = Density of body M = mass of body V= volume of body Given  L = 10foot B =…

Q: True or False? The term NPS stands for Non Plastic Section.

A: Actually the answer of this problem is little bit tricky. Because there is lot's defination or full…

Q: 40 mm 200 mm 40 mm

A:

Q: 3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

A:

Q: Name the parts shown on the bolted joint element below, respectively. 3 Grip- washer - threads Head…

A:

Q: 5. In some cases of repairs of girders damaged by collision, the damage is severe what is used?

A: To find: What is used when repair of griders damaged by collision.

Pressure and Stress