QUESTION 9 Six PV modules are connected in series to a load. Each module has Voc = 48 V and Isc=3.2 A. what is the total Voc and Isc? O Voc = 240 V & Isc = 3.2A O Voc = 48 V & Isc = 3.2 A O Voc = 48 V & Isc = 16 A Voc = 288 V & Isc = 3.2 A QUESTION 10 What are Photovoltaic Cells or solar cells made of O Steel O Concrete O Plastic Silicon

QUESTION 9 Six PV modules are connected in series to a load. Each module has Voc = 48 V and Isc=3.2 A. what is the total Voc and Isc? O Voc = 240 V & Isc = 3.2A O Voc = 48 V & Isc = 3.2 A O Voc = 48 V & Isc = 16 A Voc = 288 V & Isc = 3.2 A QUESTION 10 What are Photovoltaic Cells or solar cells made of O Steel O Concrete O Plastic Silicon

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
For the circuit shown in figure. For the circuit shown in Figure IF IB= 40 MA , VBB= 6v, RE= | Ksr, P= 80o FRc Re VeB Re The value of IE is . . mA..* О 3.24 O 4.24 O 5.24 O 6.24 O 1.24 O 2.024 The value of RB is . Kohm.. * O 52.5 O 55.5 O 47.5 O 57.5 O 25.5 O 48.5 The value of Vce is .. volt. NOTE: USE Rc= 3 Kohm, and Vcc= 15 volt. * O 5.04 O 2.04 1.04 O 4.06 O 4.04 O 3.04 O O O O O ООО О о
Subject: Fundamental of Electronics Question: Do Theoretical Calculation to get value for VClipper PRZ v 22.347V RI ww 1602 Vi 30V 60Hz 0° a. Positive Clipper Circuit PRZ O V29.057V RI VI 30V 60Hz 0° ww 1kQ PRI PRI v 22.347V D1 v 29.057V DI 1 Hile V2 5V c. Positive Clipper Circuit + Bias Voltage PRAV-23.991V R1 VI 30V 60Hz 0º PRZ 0 1k02 b. Negative Clipper Circuit v-28.305VR1 V1 30V 60Hz 8 1 140 PREV-23.991V PRI DI v-28.305V 01 3 V2 5V d. Negative Clipper Circuit + Bias Voltage
a resistor and and capacitor are connected in parallel to a 277 v 60 hz power source. the resistor has a value of 50 ohms and the capacitor has a value of 40 uf what is the circuit power factor.
Determine the DC currents (B. Ic and le) and de juncion voltages (VBE, VCE and Vca) mA. Ic ma, E mA VBE= V. VCE Vand VCB Use 2 decimal places. RB Use the following values: VBB = 3V RB = 4 kQ Rc = 166 0 Vcc = 19 V BDC = 70 %3D %3D VCC RC VBB
Which one is correct? A variable capacitor bank may be required to improve power factor, depending on the load. Power factor correction always results in a power factor greater than 0.9. Power factor correction has an impact on active power flow on the system .(i.e. MW value) A capacitor bank is always going to improve the power factor.
Determine the approximate value of VGG of Figure 52. VDD T15V 1.5kQ Q1 V, = 9.5V 1MQ = 8mA DS V =- 4.5V EVGG Figure 52. 1.453 V -1.2 V -7.547 V O -3.281 V
The following forward converter (for questions 8-12) has the following parameters. Vin=40V, Vout=10V, Pout= 50W. The duty cycle is 40%. The primary side winding Np has 16 turns. Nr : Np: Ns Vsupply Load Vout AD: Switch S (Draw the circuit with Visio) 9. What is the turns ratio between the primary side and the secondary side winding? A. Np: Ns = 16:10 B Np:N,= 16:5 C. Np:Ns = 16:7 D. None of the above 10. Assume the auxiliary winding NT has 20 turns, what is the maximum voltage on the power switch? A. 40V В. 72V С. 80V D. None of the above 11. Still assume the auxiliary winding has 20 turns, what is the maximum voltage on the diode D1 and D2? A. 10V, 10V B. 20V, 25V C. 25V, 25V, D. 20V, 20V 12. For the above Forward converter, which of the following auxiliary winding designs will ensure fully transformer core de-magnetizing in every switching cycle? A. NT= 12 turns B. N= 30 turns C. N= 50 Turns D. All A, B, C are ok
please answer number 11
Please show solution clearly
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Please address the question in the attached photo. Thank you.