### Question 3: What is the effect as more inductors are added in parallel to a circuit?#### Options:A. Increased total inductance. B. Increased total inductive reactance. C. Increased total resistance. D. Increased total circuit current.**Explanation:**When inductors are added in parallel to a circuit, the total inductance (L_total) decreases, unlike when they are added in series where the inductances simply add up. In a parallel circuit, the total inductance can be calculated using the formula:\[ \frac{1}{L_{total}} = \frac{1}{L_1} + \frac{1}{L_2} + \ldots + \frac{1}{L_n} \]- **Option A** is incorrect because the total inductance decreases, not increases.- **Option B** is incorrect because inductive reactance depends on both inductance and frequency, but it would not necessarily increase as inductors are added in parallel due to the decrease in total inductance.- **Option C** is incorrect as inductors do not primarily affect resistance directly.- **Option D** is relevant because adding more inductors in parallel will decrease the total inductance, which can lead to a decrease in the reactance and thus, under certain circumstances, might increase total current in the circuit.**Therefore, the correct answer is likely related to the overall effect on circuit current. Further details based on specific conditions of the circuit would be required to conclusively determine the impact.**

If inductors are connected in parallel then ignoring the coupling effect the total inductance…

What is the effect as more inductors are added in parallel to a circuit? A. Increased total inductance. B. Increased total inductive reactance. C. Increased total resistance. D. Increased total circuit current.

What is the effect as more inductors are added in parallel to a circuit? A. Increased total inductance. B. Increased total inductive reactance. C. Increased total resistance. D. Increased total circuit current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Which change to the circuit will not extend the charging time of one time constant. a. Increasing…

Q: Consider the circuit shown in Figure Q1(d), calculate the equivalent inductance, Leq at terminal…

Q: Calculate the inductance (H) of an air cored coil that has a length of 9 cm, a core with rectangular…

A: Consider the formula for the inductance of the air cored coil is, L=μN2Al Here, N is the number of…

Q: d) Which of the 3 capacitors will have the same potential difference across it as the power source?…

Q: Discussion Question 1: A rectangular block of iron is 2cm x 2cm x 30cm. How would you connect this…

A: A rectangular block of iron which has the dimensions of 2 cm× 2 cm × 30 cm. So now if we connect it…

Q: Describe the voltage across and the current through the inductor combination in both charging and…

A: Given: the circuit diagram consists dc source, resistor, and capacitor I) when the source is…

Q: Assume all inductance values are known. Please explain how to find the equivalent inductance as…

A: Step 1:Step 2:

Q: An uncharged capacitor and bulb are connected in series with a battery. Describe and explain what…

A: An uncharged capacitor and bulb are connected in series with a battery as shown below,

Q: Refer to the circuit shown in Figure Assume that the inductor has a wire resistance of 0.2 Q and the…

A: The circuit diagram as shown below: The switch is opened after some time, the circuit parameters…

Q: 2) a)For the following circuit find the total capacitance and inductance and hence find the total…

A: The given circuit diagram is shown below,

Q: Calculate the total inductance at the terminals a-b, for the circuit shown in FigureQ2(b). 10mH 5mH…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: A) Determine the power dissipation of each bulb the moment after the switch is closed. B) Determine…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

AC xuf lac V ac 21. The simple AC powered circuit above is being measured for AC current and voltage across a 1uF capacitor. The measured current is 200mA and the measured voltage is 40V. (note: 2 separate questions follow) a. Calculate the capacitive reactance, Xc. b. Calculate the voltage frequency.
Inductors of 1 H and 2 H are connected in series to a 440-V, 60-Hz power supply. Determine the total current flow for the circuit. Repeat for the two inductors connected in parallel to the power supply.
In the circuit below, switch S is initially disconnected from points A and B. The switch is then connected to A. What is the current and voltage in the resistors and inductor: a) as soon as the switch is turned on b) long after the key is turned on. The switch is then suddenly disconnected from A and connected to B: c) What is the current in the resistors at that moment? d) What is the voltage in the inductor? e) After that moment, what is the total energy dissipated by the resistors?
The figure displays two circuits with a charged capacitor that is to be discharged through a resistor when a switch is closed. In figure (a) below, R₁ = 23.32 and C₁ = 5.04 μF. In figure (b) below, R2 = 10.82 and C₂ = 8.10 μF. The ratio of the initial charges on the two capacitors is 902/901 = 1.61. At time t = 0, both switches are closed. At what time t do the two capacitors have the same charge? 0.0 (a) (b) Number i Units
If i have a coil with an inductance 0.14 H and a resistance of 12ohm is connected across a 110V , 25Hz source. how would you make the current in the coil and the phase between the cirrent and supply voltage ?
180 is the answer amount of ohms needed on the oscilliscope. I need to transpose the equation to solve for R. I must work out an equation that equals 180 ohms R resistance that gives off 50mA of current using the transposed equation. Series impedence ,inductive reactive, phase angle formulas may need to be used. I need to get as close to 180 ohms as possible.
A 750-ohm resistor, an uncharged 1.50 uF capacitor, and a 8.00-V emf are connected in series. (a) What is the current after one time constant? (b) What is the voltage on the capacitor after one time constant?
Capscitor question
C2 The next two questions refer to the following figure. The switch is initially open and both capacitors are initially uncharged. All resistors have the same value R, and both capacitors have the same value C. R2 R3 bat R1 ww (f) 1 pt. Immediately after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) Rị and R2 (v) R2 and R3 (vi) All have the same current (g) 1 pt. A long time after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) R1 and R2 (v) R2 and R3 (vi) None have current
9. Three inductors are connected in series to a 480 volt, 60 Hz power source. The current flow in the circuit is 0.509 amp. Inductor #1 has an inductance of 1.3 henry, and inductor #2 has an inductance of 0.75 henry. What is the inductance of inductor #3? (Assume all inductors to be pure inductors.)
a) With switch J2 open, close switch J1. Estimate the time it takes to do it. Obtain the equations for the voltage and current of the capacitor. Determine the energy stored by the capacitor. b) Open switch J1, close switch J2. Estimate the time it takes to do it. Obtain the equations for the voltage and current of the capacitor.